説明
Printed parts do not fail at the design stage. They fail at layer four hundred.
Every FDM print is a stack of decisions: extrusion temperature, flow, cooling, and above all the consistency of the feedstock going in. A spool that measures 1.72 mm on the outside of the coil and 1.78 mm near the core will print a wall that looks fine and measures wrong. A spool with trapped moisture will hiss quietly at the nozzle and leave voids you only find when the part snaps.
The specification that matters here is the boring one nobody prints on a hero banner: plus or minus 0.02 mm on a 1.75 mm filament, held across the full 330 metres in a 1.1 kg roll. That tolerance is what lets you run a flow calibration once and trust it for the next nine rolls. The PLA+ blend pushes impact strength to roughly 8 kJ/m2 by the manufacturer's figure, two to three times ordinary PLA, which is the difference between a bracket that survives a drop and one that shatters along a layer line. Printing window is 205 to 215 degrees C at 50 to 100 mm/s, or 215 to 245 degrees C when you want to move faster.
Ten rolls is not a bulk discount. It is a production lot: one colour, one diameter, one drying and winding standard, enough for a full week of printing without a mid-project supplier change.
Tolerance is the only specification that compounds. Buy it once, not per spool.
Why the Case Beats the Single Spool
- ✦Plus or minus 0.02 mm diameter tolerance held across the roll, so flow calibration transfers between spools instead of being redone.
- ✦Vacuum-sealed with desiccant per roll, which is what keeps the 100 percent no-bubble claim honest in humid workshops.
- ✦PLA+ impact strength around 8 kJ/m2, roughly two to three times standard PLA, for parts that get handled rather than displayed.
- ✦1.1 kg net per roll, about 330 m at 1.75 mm, so a case yields roughly 3,300 m of continuous production.
- ✦Neatly wound with no crossovers or knots, which eliminates the mid-print snag that ruins a fourteen-hour job.
- ✦Printing range 205 to 245 degrees C, so the same roll serves detail work and fast draft work.
- ✦Low shrinkage and warp resistance on unheated beds, with 50 to 60 degrees C bed temperature as the sweet spot.
Technical Specifications
- Diameter: 1.75 mm (also offered in 3.0 mm on some colourways)
- Tolerance: plus or minus 0.02 mm
- Net weight: 1.1 kg per roll, 10 rolls per case
- Filament length: approx. 330 m per 1.1 kg roll at 1.75 mm
- Material: PLA+ blend, RoHS and REACH compliant
- Nozzle temperature: 205-215 C at 50-100 mm/s; 215-245 C at 100-200 mm/s
- Bed temperature: 50-60 C
- Impact strength: approx. 8 kJ/m2 by manufacturer figure
- Spool handling: Vacuum sealed with desiccant, tangle-free winding
- Shelf life: 12 months sealed; reseal or dry after opening
Where It Earns Its Place
Small-batch manufacturing is the core buyer: print farms running the same bracket or jig for weeks, design studios doing functional prototypes where dimensional repeatability decides whether the client signs, and schools and makerspaces where ten students share one material standard so prints are comparable.
It is also the sensible case for the serious hobbyist who has learned that a failed fourteen-hour print costs more than the filament saved by buying the cheapest spool on the marketplace.
Before You Load the First Spool
Do I need to dry this filament before use?
Not from a sealed roll, assuming it was stored intact. Once a roll is open in a humid workshop, dry it at 45 to 50 degrees C for four to six hours. PLA+ absorbs moisture slowly but it does absorb it, and the first symptom is fine stringing that no retraction setting fixes.
Will PLA+ print on a printer tuned for standard PLA?
Mostly yes. Start from your PLA profile, raise nozzle temperature by about 10 degrees C, and expect slightly better layer adhesion. Run a flow calibration on the first roll and record the number on the case.
Is the diameter tolerance guaranteed per roll or per case?
The tolerance applies to the filament, and the case benefit is that all ten rolls come from one production run. Measure a metre from a new roll with calipers if you want certainty for a tolerance-critical job.
Can I mix colours in one case?
The case is sold in single-colour configurations, which is deliberate: single-colour lots keep the printing profile stable. If you need multiple colours, order separate cases rather than mixing, because pigment loading differs between colours and shifts flow slightly.
Is this food-safe or medically safe?
No. FDM parts are not food-safe or implant-safe regardless of feedstock, because layer lines harbour bacteria and brass nozzles contain lead. Use it for functional and decorative parts, not contact applications.
What happens if a roll is tangled mid-print?
The winding standard on this lot is designed to prevent crossovers. If you do hit a snag, stop the print, free the loop, and resume, do not pull against it. Pulling against a tangle stretches filament and changes diameter for several metres.





The EastSupplier Promise
Every unit is inspected before it leaves the warehouse, packed against transit damage, and backed by a 30-day return window. If a specification on this page does not match what arrives, we replace it. Questions before you order go to a human, not a bot.
Customer Reviews
Payment and Security
お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません
