Descrizione
Building a battery pack is the point where a hobby becomes a responsibility. Thirty cells, sixty welds, and one weak joint is enough to raise resistance, generate heat and turn a neatly assembled pack into a hazard. The Nickel Point exists to make that joint consistent rather than hopeful.
It runs a double pulse discharge at up to 1200 amps with 8000 watts of peak power, adjustable from zero upward, and that adjustability is what allows the same tool to weld 0.1 mm nickel strip for a small pack and 0.3 mm strip for a high current build without scorching the cell beneath it. The welding pen is built for conductivity and low contact resistance, so the energy goes into the joint instead of warming the cable.
The machine carries its own 9600 mAh lithium battery, which means it works on a bench, in a workshop or on a garage floor without a tether. Input runs from 100 to 240 volts through the supplied adapter, output is 8.4 volts, and the ABS shell is surface anodised to resist wear from the sort of handling a workshop tool receives.
The whole unit measures roughly 15 x 9.8 x 5 cm with a 47 cm pen, so it stores in a tool drawer rather than claiming bench space. A one metre roll of nickel tape and a sheet of sanding paper are included so the first pack can be welded the day the parcel arrives.
A battery pack is only as good as its worst weld. Weld all of them properly.
Key Features
- ✦ 8000W peak power with up to 1200A welding current, adjustable from zero
- ✦ Double pulse discharge for clean joints on 0.1 to 0.3 mm nickel strip
- ✦ Built-in 9600 mAh lithium battery, no mains tether on the bench
- ✦ Low resistance welding pen with a 47 cm reach into the pack
- ✦ 100 to 240V input with an 8.4V output and surface anodised ABS shell
- ✦ Compact 15 x 9.8 x 5 cm body, includes nickel tape and sanding paper
Technical Specifications
- Peak Power: 8000W
- Welding Current: adjustable from 0 to 1200A, double pulse
- Input Voltage: 100 to 240V AC
- Output Voltage: 8.4V maximum
- Built-in Battery: lithium, 9600 mAh capacity
- Nickel Strip Range: 0.1, 0.15, 0.2, 0.25, 0.3 mm
- Welding Pen: approximately 47 cm, low contact resistance
- Machine Size: approximately 15 x 9.8 x 5 cm
- Housing: ABS with anodised surface treatment
- Included: spot welder, power adapter, 1 m nickel tape, sanding paper
- Compatibility Note: copper, aluminium, gold and silver strip cannot be spot welded with this method
Where It Belongs
People rebuilding drill and e-bike packs use it because the adjustable current lets them match the strip thickness to the cell without guessing. Repair shops servicing cordless tool batteries value the double pulse because a second pulse cleans the joint and lowers resistance. Solar and power station builders assembling 18650 packs use it on the bench where a mains powered welder would need a socket and a longer cable. It is also the tool of choice for anyone who has already ruined one pack with a cheap single pulse unit.
The EastSupplier Promise
- Sourced and checked by our own team, never drop-shipped blind from a third party.
- Tracked shipping with a real order reference, on every parcel.
- 30-day resolution window if the item arrives damaged or not as described.
- Bulk and trade pricing available for repeat buyers and event suppliers.
Frequently Asked Questions
Q: Can it weld 0.3 mm nickel strip?
Yes. The adjustable current range and double pulse discharge are designed for strip from 0.1 mm up to 0.3 mm. Thicker nickel requires higher current and a shorter pulse duration.
Q: Does it need to be plugged in?
No. It runs on the built-in 9600 mAh lithium battery, so it works away from a socket. The supplied adapter recharges it from a 100 to 240V supply.
Q: Can it weld copper or aluminium?
No. Copper, aluminium, gold and silver strip cannot be welded using this resistance spot welding method. Use nickel strip or nickel plated steel.
Q: What comes in the box?
The spot welder itself, a power adapter, one metre of nickel tape and a sheet of sanding paper. Battery cells are not included.
Q: How do I set the current?
Start low and increase until the weld holds a firm pull test without a burn mark through the strip. The correct setting depends on strip thickness, so test on spare material first.
Q: Is it suitable for a beginner?
Yes, with care. Practise on scrap cells and strip before working on a live pack, and always check polarity before discharging.
Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.