The Silicon Deck | eMMC Storage Module for NanoPi with microSD Adapter

Save 20%
East Supplier PlatformSKU: 4000402961538-32G

Color: 32G
Price:
$221.79 $277.24

Tax included Shipping calculated at checkout

Stock:
In stock (1275 units), ready to be shipped

Description

Storage Is Not Capacity. It Is Continuity. A microSD card is the part of a single-board computer that fails first. It is a consumer medium wearing a server workload: thousands of small writes a day into a controller that was never designed for them, until one morning the board does not boot and the log you needed is gone. Embedded MultiMediaCard exists because that failure mode was expensive. It is the same silicon that phones and industrial gateways have trusted for a decade, and it removes the wear-out mechanism that turns hobby hardware into unreliable hardware.

This module mounts eMMC in the footprint your board already has. The adapter carries the storage into the microSD slot, so a NanoPi K1 Plus, K2, M4, M4V2 or NEO4 boots from solid-state memory with no card to wiggle loose, no contact corrosion, and no plastic carrier to crack. Capacities run from 16GB to 64GB in the configurations stocked here, and the operating system is flashed with the vendor EFlasher route you already know: burn the EFlasher firmware to an 8GB-or-larger SD card with win32diskimager, start the board from that card, then write the target system onto the eMMC. Flashing can be driven four ways, over HDMI and USB mouse, over ssh, over the debug serial port, or from the LCD2USB accessory with its K1 and K2 keys, so a headless board in a rack is as easy to provision as a bench unit.

The point is not a faster card. The point is a computer that keeps working in the second year. This is the module for edge nodes in cabinets, signage players that must survive power cuts, retro-console builds that get switched on every evening, and any gateway where a corrupt root filesystem means a truck roll rather than a reboot.

A memory card is a consumable. This is infrastructure.


Key Features

  • ✦ eMMC storage in a microSD-compatible form factor with a dedicated adapter board
  • ✦ Capacity options of 16GB, 32GB and 64GB in the stocked configurations
  • ✦ Purpose-built for NanoPi K1 Plus, K2, M4, M4V2 and NEO4 boards
  • ✦ EFlasher provisioning: burn to an 8GB-plus SD card, boot, then flash the eMMC
  • ✦ Four flashing routes, HDMI and USB mouse, ssh, debug serial, or the LCD2USB key accessory
  • ✦ No removable-card wear-out: writes land on eMMC instead of a plastic-and-foil carrier
  • ✦ Tool-free installation into the existing microSD slot through the bundled adapter
  • ✦ Ships as a sealed module with the adapter, ready for board-level deployment

Technical Specifications

  • Module Type: Embedded MultiMediaCard (eMMC) storage module with microSD adapter
  • Capacities Stocked: 16GB, 32GB and 64GB configurations
  • Compatible Boards: NanoPi K1 Plus, NanoPi K2, NanoPi M4, NanoPi M4V2, NanoPi NEO4
  • Host Interface: microSD slot on the host board, via the supplied adapter
  • Flashing Tool: EFlasher firmware written with win32diskimager or the dd command
  • Flashing Media: SDHC card of 8GB or larger capacity
  • Flashing Routes: Graphical desktop, ssh session, debug serial console, or LCD2USB key accessory
  • Default ssh Credentials: User root, password fa, as documented for EFlasher
  • Installation: No soldering, adapter seats into the existing card reader
  • Module Origin: Mainland China, CE-marked supply chain
  • Intended Use: Edge nodes, signage players, gateways and single-board builds needing non-removable storage

Where It Belongs

The module belongs wherever a single-board computer has to survive unattended operation. In retail digital signage it replaces the card that dies after a year of write cycles. On a factory floor it gives a NanoPi gateway storage that will not walk away in someone hand. In a home-lab rack it turns a stack of boards into machines that can be power-cycled without a repair box on the shelf. Retro-console builders use it because the case never has to be opened again. Test benches, kiosk prototypes, LoRa gateways and vehicle computers all share the same requirement: storage that is part of the board, not a part the board depends on.


Frequently Asked Questions

Q: Which boards does this module fit?

It is built for the NanoPi family, specifically K1 Plus, K2, M4, M4V2 and NEO4. The adapter seats into the board microSD slot, so no rework is needed.

Q: How is the operating system installed onto the eMMC?

Write the EFlasher firmware to an SDHC card of at least 8GB, boot the board from that card, and EFlasher copies the chosen system image onto the eMMC. Once finished, power down, remove the SD card and boot from the module.

Q: Can I run it headless?

Yes. EFlasher can be driven over ssh on the local network, over the debug serial port, or from the LCD2USB accessory using its K1 and K2 keys. Only the graphical route needs a monitor.

Q: What is the difference between eMMC and the microSD card I already use?

eMMC is the same class of memory soldered into phones and industrial gateways. It removes the removable-card wear-out and contact problems, which is why it is the standard choice for boards that run continuously.

Q: Do I have to remove the module to reflash it?

No. Reflash over the network, serial console or LCD2USB accessory while the module stays in place inside the enclosure.

Q: What is included with each module?

The eMMC module itself plus the microSD adapter that carries it into your board card slot. Storage capacity is selected at checkout.


The EastSupplier Promise

Every unit is inspected before it leaves the warehouse. If a specification on this page does not match what arrives, we cover the return shipping and replace it. English-language support answers within one business day, and replacement parts for this category are stocked so that a working unit stays working.

Customer Reviews

Customer Reviews

Based on 4 reviews
75%
(3)
25%
(1)
0%
(0)
0%
(0)
0%
(0)
D
Daniel K.
Right part for headless boards

Provisioned four NEO4 gateways from the serial console with no monitor attached. Capacity options made it easy to standardise on one size across the fleet.

P
Priya N.
Works, adapter seats well

Module and adapter arrived together and fit the slot properly. Took me a few minutes to understand the LCD2USB flashing route, but flashing over ssh is simpler and needs no monitor.

E
Elena R.
Finally non-removable storage

This went into a signage player in a shop window. The old card died every summer from the write cycles. The eMMC module has been running for months without a single failure.

M
Marcus T.
Boots every time now

Replaced the microSD in a NanoPi M4 that had corrupted twice in a year. Flashed with EFlasher over ssh in about ten minutes and the board has been up since. No card to reseat when the cabinet gets bumped.

Payment and Security

PayPal

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently Seen