説明
Heat Is The Only Enemy Of Hashrate. Every degree above junction temperature specification is a silent tax on your ASIC's throughput — reducing efficiency, shortening lifespan, and eating into the razor-thin margins that separate profitable mining from a space heater with a power bill. The Hash Guardian is not a fan. It is a thermal insurance policy for the silicon that earns your keep.
At 6000 RPM, this 120mm axial fan pushes over 250 cubic feet per minute through the dense fin stacks of a Bitmain Antminer — enough static pressure to overcome the impedance of a dust-filtered intake, a crowded mining shelf, and the backpressure of an exhaust duct, all simultaneously. The dual ball bearing assembly is not a cost-saving choice. It is an engineering mandate: sleeve bearings degrade within 6-12 months at the 40°C+ ambient temperatures common in mining environments. Dual ball bearings are rated for 70,000 hours at those same temperatures — over eight years of continuous operation before degradation begins. The 38mm frame depth (not the consumer-grade 25mm) houses a rotor large enough to sustain 6000 RPM without cavitation or blade flutter.
Compatibility spans the Bitmain ecosystem: S19, S19 Pro, S19j, S19j Pro, T19, S17 Pro, T17, L3+, and L3++ all share the 120mm mounting pattern and 4-pin PWM header this fan is built for. The 12V DC draw means it runs directly off the Antminer control board's fan header — no external power supply, no voltage converter, no wiring workaround. Plug it in, and the ASIC's firmware governs the fan curve exactly as it would for the original. What changes is the margin: cooler junction temperatures, fewer rejected shares, and a hashboard that reaches its rated lifecycle instead of burning out at 60%.
The ASIC mines the coin. The fan mines the uptime.
Key Features
✦ 6000 RPM sustained speed — over 250 CFM airflow for dense ASIC thermal management
✦ Dual ball bearing construction — 70,000-hour MTBF at 40°C, outlasting sleeve bearings by 6-8x in mining duty
✦ 38mm deep frame — the industrial form factor that sustains high RPM without blade deformation
✦ 4-pin PWM connector — plug-and-play with all Bitmain Antminer control boards
✦ Broad Bitmain compatibility — S19 / S19j / S17 Pro / T17 / T19 / L3+ / L3++ and more
✦ 12V DC direct power — no external adapter or voltage step-down required
✦ Balanced rotor for reduced vibration — less harmonic noise through the mining shelf
Technical Specifications
- Rated Voltage: 12V DC
- Speed: 6000 RPM
- Compatibility: Bitmain Antminer S19 / L3+ / L3++ / S17 Pro / T17 / S19 Pro / S19j / S19j Pro / T19
- Connector: 4-Pin PWM Header
- Bearing Type: Dual Ball Bearing
- Airflow: 250+ CFM (estimated at 6000 RPM)
- Noise Level: ~65 dBA at full speed
- Dimensions: 120mm x 120mm x 38mm
- Power Draw: ~36W at 12V / 3A
- MTBF: 70,000 Hours at 40°C
Application Scenarios
The Hash Guardian is purpose-built for cryptocurrency mining environments, but its high-static-pressure profile serves adjacent industrial applications. In ASIC mining farms, it replaces worn or failed OEM fans on Bitmain S19 and L3+ series units — the single most common failure point in a mining operation. A single fan swap takes under three minutes with a Phillips screwdriver and restores the thermal envelope that determines hashrate stability. In immersion cooling setups, the Hash Guardian moves air across the dry side of heat exchangers where consumer fans stall against the backpressure. Beyond mining: it serves as a drop-in upgrade for server rack cooling, 3D printer enclosure exhaust, laser cutter fume extraction, and any application demanding sustained high-RPM airflow in a 120mm form factor. For miners running multiple units, stocking a set of Hash Guardians eliminates the downtime risk of waiting for replacement fans — a single day of lost hashrate on an S19 at current difficulty is more expensive than a full fan swap kit.
Frequently Asked Questions
Q: Will this fan work with my Antminer S19j Pro?
A: Yes. The S19j Pro uses two 120mm x 38mm 4-pin PWM fans — the Hash Guardian is a direct drop-in replacement for both the intake and exhaust positions. The Antminer firmware will auto-detect and control the fan speed via PWM.
Q: How loud is this fan at full speed?
A: Approximately 65 dBA at 6000 RPM — comparable to the OEM Antminer fan. This is not a quiet fan; it is a performance fan. Mining environments typically operate at 70-80 dBA ambient, so the Hash Guardian is within expected noise profiles for the application.
Q: How do I know when to replace my mining fans?
A: Three indicators: (1) the Antminer kernel log shows fan speed errors or RPM below the expected curve, (2) chip temperatures consistently exceed 80°C even after cleaning, (3) audible bearing noise — a grinding or clicking sound that indicates ball bearing degradation. Replace preemptively at 12-18 months for continuous-operation environments.
Q: Does this fit the L3+ as well?
A: Yes. The L3+ uses the same 120mm mounting pattern and 4-pin PWM header. The Hash Guardian is a direct replacement for both the front and rear fans on all L3+ units.
Q: What's the difference between this and a standard PC case fan?
A: Three critical differences. First: the 38mm frame depth vs. a typical 25mm PC fan — the deeper rotor generates significantly more static pressure, essential for pushing air through the dense heatsinks in an ASIC. Second: dual ball bearings vs. sleeve or rifle bearings — at continuous 40°C+ operation, sleeve bearings fail in months; dual ball bearings last years. Third: the blade geometry is optimized for pressure, not silence — a PC fan prioritizes low noise; the Hash Guardian prioritizes airflow through impedance.
Q: Does it come with mounting screws?
A: The Hash Guardian is sold as the fan unit. Most Antminer units reuse the existing mounting screws from the original fan. If you need replacement screws, standard M4 x 35mm self-tapping fan screws are available at any hardware or electronics retailer.
Q: Can I run this at lower speeds for less noise?
A: Yes. The 4-pin PWM connector allows the Antminer control board to dynamically adjust fan speed based on chip temperature. In cooler ambient environments or with underclocked ASICs, the firmware will automatically reduce RPM, lowering both noise and power consumption. The dual ball bearing design operates smoothly across the full PWM range from ~1200 to 6000 RPM.
Customer Reviews
Pagamento e Segurança
お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません
