What is a terminal indicator light?
Terminal indicator lights refer to devices that use light to monitor the operation or position state of circuits and electrical equipment.
The terminal indicator light is usually used to reflect the working state of the circuit (with or without electricity), the working state of the electrical equipment (running, down, or testing), and the position state (closed or disconnected).
Usually installed in the low-voltage distribution device of the screen, disk, table, cabinet on the panel, some low-voltage electrical equipment, instruments on the disk, or other prominent position.
Terminal indicator light reflecting the working state of the equipment. Usually, when the light is on, it means the equipment is live; when the light is off, it means the equipment is out of power.
Pilot lights and indicator lights vary primarily by the type of lamp used.
Incandescent lights emit light through a thin wire (filament) which becomes hot when electricity flows through it. It can operate on either AC or DC circuits; however, these devices are relatively inefficient, generate heat, and have shorter operating life spans than LED pilot lights.
LED lights are semiconductor light sources that require DC to operate. If a DC circuit is not available, an LED driver can be used to supply the appropriate DC voltage and current.
They have the advantage of smaller size, longer lifetimes, and lower energy requirements than incandescent or fluorescent lights. Some LED lights can change color with the polarity of the current.
Fluorescent lights utilize fluorescent bulbs in which house electrodes at both ends of the tube and argon and mercury vapor throughout.
A phosphor coating on the inside of the tube emits light through the emission of ultraviolet light from the excitation and stabilization of mercury atoms.
Fluorescent bulbs tend to be more energy-efficient and longer-lasting than incandescent bulbs, but are less commonly used as indicators.
Halogen lights utilize a tungsten filament, inert gas, and a small amount of a halogen to emit light.
This combination allows for higher temperature filaments which can produce more light given the same energy (higher color temperature).
This favors their use as daytime indicators and warning lights which require brighter light.
Product Specifications
Important specifications for pilot lights and indicator lights include electrical requirements such as voltage, size, and color.
Based on the application, mounting style (panel, PC board) and terminal type (feed-through, wire leads, etc.) will also need to be considered.
To rate LEDs for use as pilot lights and terminal indicator lights, manufacturers state the luminous intensity in candelas, which is a function of the viewing angle.
Applications
Pilot and indicator lights are used as malfunction lights in automatic equipment, voice mail lights for telephones, condition panels, and dashboard lights for vehicles.
They can also be built into switches. Indicator lights are very versatile and are usually used in The coffee machine, The water heater, Water dispenser, Baked Fried furnace, Meat grinder, automation, Test equipment, Disinfection cabinet,
The dishwasher, Barbecues, Cleaning machine, Food machinery, The freezer, A blender, blender, The fault, Modified car, Shoe machine, Refrigeration equipment, Insulated rice stand, Cooking stove, Waterproof air case,
Induction cooker, Lampblack purifier, Cooking noodles barrels, Vending machines, Charging pile, The solar energy, Powerbox, The subway, The dashboard, wine, Audio equipment, Distribution box, Sound effector, The cinema,
Medical equipment, Car panel, player, Audio equipment, Distribution box, Medical equipment, Power amplifier player, Education, school lab, The generator, Electric welding machine, Cable tray, inverter, Voltage regulator,
The access control device, Automobile, and motorcycle accessories, Industrial air purifier
Our company mainly produces and sells indicators for LED and neon bubbles.
How many ways to install the terminal indicator light?
There are two ways to install the terminal indicator light.
- Screw type, the terminal indicator light is installed on the panel, and then the nut is screwed on.
- Bayonet type, the terminal indicator light is directly stuck into the mounting hole, fast and convenient.
How many types of indicator lights?
There are too many types of the terminal indicator light, such as raised head, concave head, flat head, etc., you can also customize the style according to the individual needs, please check www.indicatorlight.com for details
How many materials does the terminal indicator light have?
The terminal indicator light has two kinds of materials: plastic and metal. The plastic terminal indicator light is of high-cost performance. The metal indicator has an explosion-proof function and a high-end atmosphere, which is basically used for high-end products.
The metal indicator light has a copper material type, stainless steel type, and zinc alloy aluminum black type, customers usually use chopper material in the market, stainless steel material, especially 316 stainless steel material, is basically used in the environment with corrosion, such as seawater and sulfuric acid place.
Zinc alloy aluminum black type’s appearance is better.
How many mounting holes of the indicator light?
The mounting hole is always round, the sizes are 6 mm, 8 mm, 10 mm, 12 mm, 14 mm, 16 mm, 19 mm. 22 mm. etc.indicator light also has square hole installation.
How many voltages does the terminal indicator light have?
Voltage is 2v 3v 5v 6v 12v 24v 36v48v110v120v220v250v380v 750V ,etc
How many LED colors does the terminal indicator light have?
LED colors are red, green, yellow, blue, white, purple,
Is there a bi-color indicator light?
The indicator light has bi-colors, such as red and green, red and blue, blue and green, etc
Is there a tri-color indicator light?
The indicator light also has tri-color, such as red green blue, red green yellow indicator light, etc
Is there a waterproof terminal indicator light?
There are waterproof and non-waterproof indicators, and the waterproof indicator has IP67 and IP68 waterproof grades
What is the international standard voltage tolerance of the terminal indicator light?
The international voltage standard of the plastic indicator light is passed by the voltage of 2000V, the test time is 5 seconds, the metal indicator light is 1800V, the test time is 5 seconds
How many ways to connect to the terminal indicator light?
There are two kinds of connections: wire and terminal connection.
Why choose FILN company’s indicator light?
FILN is a professional indicator light manufacturer with the most complete types of indicators in the world.
How old is the factory
FILN has 20 years of professional manufacturing experience in indicator lights.
What are the certifications of indicator light?
FILN company indicator light has gotten the following international certification: the United States UL, Germany VDE, EU CE, EU RoHS,
Is there a waterproof indicator light?
FILN has waterproof IP67 and IP68 indicator lights.
Can the indicator light be made according to my requirements?
FILN company has a professional light design team, who can quickly develop products according to the needs of customers.
How do you make money by selling lights?
FILN company’s indicator lights are all designed by FILN indicator light design team, most of them have design patents, which is different from other companies’ products if you sell FILN indicator light products, I believe that it will bring a lot of money and high profits to you.
Does the indicator have a MOQ? What is the MOQ?
FILN company is a professional factory, and there is no MOQ limited, so you can start from one piece indicator light, do not worry about the minimum order.
How long is the quality warranty of the indicator light?
The quality of the FILN indicator light is very high, with a shelf life of 10 years, during which time if quality problems, all free replacement.
Do you have a heat resistant indicator?
FILN’s indicator lights have 180℃ heat resistant, the plastic is made up of 200℃ nylon PA66, and the wire is made up of 200℃ silicone.
Are there flashing lights?
FILN can make single flashing lights according to customers’ needs.
Introduction of 12mm FL1P-12QJ-1 indicator light
Following is a picture of a 12mm FL1P-12QJ-1 terminal indicator light
Following is a drawing of a 12mm FL1P-12QJ-1 terminal indicator light
The FL1P-12QJ-1 terminal indicator light product is introduced as follows
12mm 12V terminal indicator light metal shell adopts numerical control technology processing, to ensure the appearance of the atmosphere beautiful, high precision
12V green terminal indicator light LED adopts a non-polar LED, which can be used by customers without any positive or negative level. The service life of LED is 50,000 hours
LED indicator IP67, installation aperture is 12mm
Socket head indicator voltage can do 3V6V 12V 24V110V 220V 380V and so on
12V ip66 plastic terminal indicator light can be red, yellow, green, blue, and white in 5 colors
LED terminal indicator light voltage can do 3V6V 12V 24V110V 220V 380V and so on
12mm plastic terminal indicator light can be red, yellow, green, blue, and white in 5 colors
Terminal indicator lights are very versatile and are usually used in The coffee machine, The water heater, Water dispenser, Baked Fried furnace, Meat grinder, automation, Test equipment,
Disinfection cabinet, The dishwasher, Barbecues, Cleaning machine, Food machinery, The freezer, A blender, blender, The fault, Modified car, Shoe machine, Refrigeration equipment, Insulated rice stand, Cooking stove,
Waterproof air case, Induction cooker, Lampblack purifier, Cooking noodles barrels, Vending machines, Charging pile, The solar energy, Powerbox, The subway, The dashboard,
wine, Audio equipment, Distribution box, Sound effector, The cinema, Medical equipment, Car panel, player, Audio equipment, Distribution box, Medical equipment, Power amplifier player, Education, school lab, The generator,
Electric welding machine, Cable tray, inverter, Voltage regulator, Access control device, Automobile, and motorcycle accessories, Industrial air purifier, FILN indicator light through the United States UL certification, Germany VDE certification,
European Union CE certification, ISO90001 quality management system certification, and so on, the quality is stable, the style is complete, can be customized according to the customer’s needs of different styles of terminal indicator light.
Product Item: FL1P-12QJ-1
Panel Mount Diameter:12mm
Contact Way: Pins
Install Way: push snap-in
Lamp Type: LED((Our led is a bidirectional led.no difference of anode and cathode, you can connect any way you want)
Rated voltage: AC/DC,3V、6V、12V、24V、220V、380V
Lamp Color: red yellow blue green white
Product Design: Flathead
Shell Material: PC
Base Material: PA66 nylon
Terminal Material: brass
Applications: Coffee machine, kitchen equipment, household appliances, automobiles, medical equipment, industrial equipment, etc
Component name material
lens: PC plastic
Metal body: H59 brass or 204 stainless steel
washer: T10 Cold Rolled Steel
rubber ring: SIL silica gel
nut: H59 nickel-plated brass
housing: PA66 nylon
Light source: LED
Resistor: Metal film
Cable: it also can be made with wire
plug-in:C2680 RoHS brass
Items parameter
Rated voltage:3V-780V DC or AC
rated current:20mA
rated power:0.2W
Insulation and voltage resistance:1800V
working life:100000h
electrical life:100000
cold-resistant:-40℃
heat-resisting:80℃
That is all for the 12mm FL1P-12QJ-1 indicator light, besides, we also have a symbol terminal indicator light.
Symbol Indicator lights are used in a wide range of applications, such as coffee machines, water dispensers, car modifications, gas stations, and audio and video equipment.
A clear icon or text with the color of the light makes the indicator function more clear. Make the equipment more beautiful, reduce the text description, and make the customer easier to understand and operate.
The terminal indicator light sizes we can do : 8mm/10mm/12mm/14mm/16mm/19mm
Available Volt: 3V/6V/12V/24V/48V/110V/220V/380V
Connection method: with wire / solder fillet
Shell color: metal plating black/chrome plating
Below are some of the icons we currently do for our customers. In addition, we can also customize other icons that customers want, no MOQ
- Introduction to the Company
Yueqing Yulin Electronic Co., Ltd, which is founded in 1998, is a professional Push Button switch /indicator light/rocker and guitar switch manufacturer with ISO9000 management system certification in domestic.
We have over 20 years of history in producing and developing the push button switch series, indicator light series, rocker switch series, and guitar switch series, and keep developing 1~2 new series production each year.
Now, we have about many series push button switches, indicator lights, rocker switches, guitar switches, and more than 30 patents.
At present, the company has 235 employees, including 23 salesmen, 10 technicians, 6 quality personnel, and 20 administrative and management personnel.
Our goal is to provide customers with professional product services and customized solutions.
CNFILN strives to be a leader in segments.
No matter the series you choose, all of our switches offer an advanced design, quick break contacts, a self-cleaning feature, and high reliability. Furthermore, they have long lives, durable, and easy to install.
And we have obtained a number of certification certificates including CCC, CE, RoHS, and UL.
We focus on enhancing the intangible assets. What we seek is satisfying our customers’ needs.
So we always keep the company at its best in perseverance by transmission in the market. With the expansion of the international market, we swear to be the global leader in the industry of switch.
Corporate mission: ingenuity China, scientific and technological innovation, subversion of the future, push the world
Corporate vision: create the world’s safest, most customer-informed, most beautiful switch, become the world’s first.