説明
Most filament problems are not settings problems. They are winding problems: a spool wound under tension at the factory, a strand that crosses itself three layers down, a print that fails at hour six because the extruder had to pull harder than the motor could manage. The extruder gets blamed, the temperature gets adjusted, and the actual cause sits on the spool holder looking perfectly normal.
This refill is wound spooless, tightly and in a single continuous lay, which is the format Anycubic uses to remove the cardboard core and the tangle risk that comes with a loosely wound spool. The material is standard PLA at 1.75 mm diameter with a 1 kg net weight, tolerant of the usual 190 to 220 degree nozzle range and a 60 degree bed. It is solid, low-odour, and consistent enough in diameter that a profile tuned on one roll carries over to the next without retuning the flow multiplier.
Spooless refills are designed to drop into a reusable spool, which is the other half of the value: you buy the material once per kilo and keep the hardware. Store the roll sealed with the desiccant pack it ships with, because PLA absorbs moisture and wet filament foams at the nozzle, which shows up as fine surface bubbles and weak layer adhesion long before it fails outright.
A failed print at hour six is almost never the printer's fault.
Built Around One Problem
- ✦Spooless refill, wound in a single continuous lay to eliminate the crossed strand that stalls an extruder
- ✦1.75 mm diameter held to a tight tolerance, so a tuned flow multiplier carries between rolls
- ✦Standard PLA, printable across the usual 190 to 220 degree nozzle range on a 60 degree bed
- ✦1 kg net weight per refill, dropping into a reusable spool to keep the hardware once
- ✦Low-odour, solid filament suitable for indoor printing in a room with normal ventilation
- ✦No cardboard core to discard, which is the part of a spool that usually ends up in landfill
- ✦Sealed with a desiccant pack, because moisture is the most common cause of surface bubbles
Numbers, Not Adjectives
- MaterialPLA
- FormSolid filament, spooless refill
- Diameter1.75 mm
- Net weight1 kg per roll
- Nozzle temperature190 to 220 C
- Bed temperature60 C
- ToleranceTight diameter tolerance, consistent across the roll
- WindingSingle continuous lay, no crossed strands
- CompatibilityFDM printers accepting 1.75 mm, reusable spool required
- StorageSealed with desiccant, dry environment
Who Ends Up Buying It
This is the consumable for anyone running a printer as a tool rather than a hobby: prototype iterations that need to finish overnight, jigs and brackets for a workshop, replacement parts printed because the original is a two week wait. Schools and maker spaces buy it because a spooless refill cuts the waste per kilo and survives being handled by people who are learning. The practical difference for a single user is the failure rate: fewer mid-print stalls means fewer half-finished parts and less material thrown away.
Where This Comes From
Sourced directly from vetted manufacturing partners, inspected before dispatch, and priced without distributor layers. If the item arrives outside specification, we replace it or refund it. Every listing on this store is curated by a human buyer, not bulk-imported and abandoned.
Before You Order
Q: Does this fit a standard spool holder?
The refill is designed to mount on a reusable spool, which then sits on any holder taking a 1 kg roll. It is not a self-supporting spool, so a bare refill needs the reusable hub before printing.
Q: What temperature should I print it at?
Start at 200 degrees with a 60 degree bed and adjust in 5 degree steps. Standard PLA on most machines lands between 195 and 210 for a clean surface; the tolerance on this filament means one profile should hold across the roll.
Q: Will the diameter stay consistent?
The winding is a single continuous lay with a tight diameter tolerance, which is what keeps flow constant from the first metre to the last. Consistency is the property that matters most in a refill, since a diameter swing shows up as surface artefacts.
Q: Is it suitable for a beginner?
Yes. PLA is the most forgiving material to print, and the spooless winding removes the tangle failure that beginners most often mistake for a machine fault.
Q: How should it be stored between prints?
Sealed with the desiccant pack, away from sunlight and radiators. PLA absorbs moisture from the air, and wet filament foams at the nozzle, producing bubbles and weak layer bonding that look like a settings problem.
Q: Does it work in an enclosure?
It works, but PLA dislikes trapped heat. Keep the enclosure vented so the chamber stays near ambient, otherwise the part can soften and lose dimensional accuracy on tall prints.
Customer Reviews
Payment and Security
お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません