説明
A tyre pressure light that will not clear is a small problem with an outsized cost. The wheel comes off, the sensor gets replaced, and then the vehicle refuses to accept it until somebody with the right tool walks over and relearns the corner.
The TireGO 808 exists to remove that second visit. It activates and reads existing sensors, programs MX-Sensor replacements at 315 and 433 MHz, and then relearns the vehicle through the OBD port, through an automatic drive cycle or in stationary mode depending on what the module supports. That three-way relearn coverage is why the tool suits a mixed fleet rather than a single marque.
Coverage runs across American, European and Asian systems, from the domestic trucks and SUVs that dominate independent workshops to the German and Japanese platforms that arrive with tighter sensor protocols. Key fob testing is built in, so a no-start complaint that turns out to be a dead fob can be confirmed at the same visit. Updates arrive over Wi-Fi, which means no cable, no laptop and no return-to-base routine.
It is a specialist instrument rather than a general scanner. It does one job at a tyre bay or a service desk, does it repeatedly, and keeps the diagnostic session short enough that the next car can come onto the ramp.
A sensor is a small part. The relearn is what makes it a repair.
Why This Configuration Works
- Three relearn paths — OBD, automatic and stationary methods cover the majority of modules on the road.
- MX-Sensor programming — writes 315 and 433 MHz sensors in the bay rather than ordering pre-programmed stock.
- Activation and readout — reads sensor ID, pressure and state before deciding on a replacement.
- Wide regional coverage — American, European and Asian platforms from the major groups.
- Key fob test — confirms a fob fault during the same visit as the tyre work.
- Wi-Fi updates — software refreshes without a cable, a laptop or a return-to-base trip.
- TPMS diagnostics and reset — clears stored faults and resets the module once the new sensor is accepted.
Technical Specifications
- Function — TPMS activation, programming, relearn and reset
- Sensor programming — MX-Sensor at 315 and 433 MHz
- Relearn methods — OBD, automatic, stationary
- Regional coverage — American, European and Asian vehicles
- Additional test — Key fob testing
- Updates — Wi-Fi, no subscription cable required
- Connection — OBD-II port
- Diagnostics — TPMS fault read and clear
- Use case — Tyre bay, service desk, mobile technician
- Brand — OTOFIX
- Category — Tyre service tools
- Intended market — Automotive aftermarket
Where it belongs
Tyre shops use it as the relearn station at the end of the bay, where a car leaves with a cleared light instead of a return appointment. Independent garages use it to handle TPMS work in-house rather than sending customers to a dealer. Mobile tyre fitters carry it because the alternative is asking a customer to drive back once the sensor has been fitted, and fleet operators use it to standardise sensor stock across mixed vehicle types.
Questions Buyers Ask Before Ordering
Q: Does it program new sensors or only read them?
A: It does both. Existing sensors can be activated and read, and MX-Sensor replacements can be programmed at 315 or 433 MHz.
Q: How does the relearn work?
A: Three methods are supported: through the OBD port, through an automatic drive cycle, and in stationary mode. Which one applies depends on the vehicle module.
Q: Will it cover my vehicle?
A: Coverage spans American, European and Asian platforms. Check your make, model and year against the supported list before ordering.
Q: Are updates paid?
A: Software updates are delivered over Wi-Fi. Confirm the current update terms for your region with support at the time of purchase.
Q: Can it test a key fob?
A: Yes. Key fob testing is included, which helps separate a fob fault from an immobiliser or battery problem.
Q: Does it need a laptop?
A: No. Updates and operations run on the tool itself over Wi-Fi, without a PC in the loop.
Q: Is it a full diagnostic scanner?
A: No. It is a dedicated TPMS tool. For engine, ABS and transmission diagnostics you need a general scan tool.
Q: What do the 315 and 433 MHz figures mean?
A: Those are the two radio bands TPMS sensors transmit on. A tool that programs both covers the sensors fitted across American, European and Asian vehicles, so one sensor part number serves more of your stock.
Q: Will it work on a vehicle with indirect TPMS?
A: No. Indirect systems estimate pressure from wheel speed through the ABS module and have no in-wheel sensor to program. This tool works with direct sensor systems, where a sensor sits at the valve.
Customer Reviews
Payment and Security
お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません