The Ten Kilo Case | PETG and ABS Filament, Ten 1kg Spools

20%セーブ
East Supplier PlatformSKU: 1005008258343723-PETG Clear green-GERMANY

Color: PETG Clear green
価格:
$181.61 $227.01

送料計算済み チェックアウト時

在庫:
在庫あり

説明

A spool that tangles halfway through a nine hour print costs more than the spool. That is the arithmetic behind the Ten Kilo Case: ten sealed 1 kg rolls of SUNLU PETG and ABS, wound on the manufacturer's own neat-winding line, boxed so that a print farm can queue work for a month without re-ordering.

PETG is the material most workshops settle on after PLA stops being enough. It takes impact, it resists acids and alkalis, it holds up outdoors, and it does not shatter when a part is dropped. Printed at 220 to 230 °C onto a bed at 60 to 70 °C, it bonds to itself well enough that layer separation becomes a rare fault rather than a routine one. The transparent colours carry light cleanly, which is why signage and light-diffusing parts end up in PETG rather than PLA.

ABS in the same case covers the jobs that need heat resistance and machining afterwards. It sands, drills, taps and vapour-smooths, which matters when a printed part has to fit an existing assembly and be finished like an injection moulding. Both materials run through any FDM machine with a heated bed, and each roll carries 320 metres of PETG or 330 metres of ABS at 1.75 mm.

Consistency is a supply decision. The print either works or it does not, and the spool decides before the nozzle does.

Inside the ten kilo case

  • ✦ Ten 1 kg spools, PETG or ABS, sealed individually
  • ✦ 1.75 mm diameter held to plus or minus 0.02 mm along the full length
  • ✦ Neat-winding line with a stated 100 percent neat rate, which is what stops mid-print tangles
  • ✦ Zero-bubble extrusion, so no popping and no voids inside a wall
  • ✦ PETG for toughness and chemical resistance, ABS for heat and post-processing
  • ✦ Colour sets include single colours and mixed five-plus-five packs
  • ✦ Spools fit standard 200 mm holders without an adapter

Filament data

  • Materials: PETG and ABS
  • Diameter: 1.75 mm, tolerance plus or minus 0.02 mm
  • Net weight: 1 kg per spool, 10 kg per case
  • Gross weight: 1.3 kg per spool
  • PETG length: 320 m per kg
  • ABS length: 330 m per kg
  • Nozzle temperature, PETG: 220 to 230 °C
  • Bed temperature, PETG: 60 to 70 °C, glue optional
  • Print speed: 40 to 60 mm/s
  • Shrinkage: low, minimal warping
  • Shelf life: 12 months in a sealed bag
  • Compatibility: all common FDM printers with a heated bed

Who prints this much

Small print farms buy the case because a single supplier and a single batch removes the variable that ruins a production run: inconsistent filament. Design studios use the mixed colour packs for prototypes and short display runs where the transparent PETG carries an LED or a light pipe. Schools and makerspaces buy ABS for parts that have to survive a workshop and be machined afterwards. Anyone printing enclosures, brackets, jigs, signage or replacement parts will find ten kilos is roughly two to three months of steady weekend use, and considerably less for a business.

Printing questions

Q: Do I need an enclosure for PETG?

A: No. PETG prints in open air. ABS benefits from an enclosure or at least a draught-free room, because a cold breeze across a large ABS part is what causes splitting.

Q: Why is my PETG stringing between parts?

A: Usually moisture and temperature. Dry the spool for four hours at 60 °C, then drop the nozzle temperature by five degrees and raise retraction slightly. PETG strings when it runs too hot.

Q: Does the spool fit a standard holder?

A: Yes. It uses the 200 mm hub that most printers and dry boxes accept, with no adapter ring needed.

Q: Can PETG and ABS share the same nozzle?

A: They can, but purge thoroughly between them. ABS residues left in a hotend that later runs PETG at a lower temperature produce black specks and weak layers.

Q: How should the unused spools be stored?

A: In the sealed bag with the desiccant, away from sunlight. Once opened, a spool will absorb moisture over weeks in a humid room, and PETG shows it as stringing and cloudy walls.

Q: Is the diameter consistent at the end of a roll?

A: The tolerance of plus or minus 0.02 mm is held across the length of the spool, which is the point of the neat-winding line. A roll that narrows toward the core causes under-extrusion on the last third of a print.

Q: Are the colours the same between cases?

A: Batch to batch, clear and translucent colours vary slightly. If a project needs an exact match across two cases, order both at once from the same listing.

Q: What can ABS do that PETG cannot?

A: Take heat and take machining. ABS holds shape in a hot car and sands or drills cleanly, which makes it the choice for functional parts that get finished after printing. PETG wins on toughness and on chemical resistance.

Q: Is ten kilos too much to buy at once?

A: Only if you print rarely. A sealed spool keeps for around a year, and buying a case costs less per kilo than buying singles, which is the reason print farms order this way.

Customer Reviews

Customer Reviews

Based on 3 reviews
67%
(2)
33%
(1)
0%
(0)
0%
(0)
0%
(0)
A
Allegra N.
Dry the spool if it strings

Straight out of the bag it printed clean. Opened a spool that had sat out for two weeks and it stringed until I dried it, so store them sealed like the listing says.

R
Reina S.
PETG that behaves

Clear green printed at 230 with a 65 degree bed and the layer adhesion is solid on brackets that take a knock. Transparency is good enough for light diffuser panels.

F
Finlay R.
Ten rolls, no tangles

Printed through four of the spools so far with zero tangles and no popping from moisture. The winding is as neat as claimed, which has not been my experience with cheaper singles.

Payment and Security

PayPal

お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません

発送予定

You may also like

Recently Seen