The Fire Pulse | 4X Ignition Coil Pack for Suzuki GSX1300R GSXR1000 Hayabusa (OEM 129700-4400)

20%セーブ
East Supplier PlatformSKU: 2251832771793363

価格:
$143.02 $178.78

送料計算済み チェックアウト時

在庫:
在庫あり (124個), 出荷準備完了

説明

Ignition is the pulse of an engine. Every misfire, every hesitation at full throttle, every hard-start on a cold morning traces back to the same root cause: the coil is not delivering the voltage the combustion chamber demands. On a Suzuki GSX-R or Hayabusa — engines that rev past 10,000 RPM and demand precise spark timing — a weak coil is not a maintenance item. It is a performance limiter.

The Fire Pulse ignition coil set replaces the factory 129700-4400 and F6T547 units with windings that match OEM electrical specifications and exceed OEM mechanical durability. Each coil is wound on a ferrite core with copper primary/secondary windings insulated by epoxy resin — the same construction method used in racing coils that endure sustained high-RPM operation. The secondary output exceeds 9825 kV at cranking, ensuring a hot, consistent spark even when the battery voltage drops during cold starts or after extended cranking.

We tested these on a 2007 GSX-R1000 that had been throwing P0302 (cylinder 2 misfire) with aftermarket coils. The Fire Pulse set cleared the code on the first startup. Idle smoothed from a loping 1100 RPM to a steady 1200. The owner reported: "It starts faster, idles smoother, and pulls clean through 8,000 where it used to stumble." Four bolts, ten minutes, one set of coils. The engine tells you when the spark is right — listen to it.

A misfire is not a part failure. It is a message from the cylinder. Answer it with the right coil.


Key Features

  • OEM-Grade Copper Windings: Primary and secondary windings use oxygen-free copper for maximum conductivity and consistent spark output throughout the RPM range
  • Epoxy-Resin Encapsulation: Full potting protects the windings from vibration, moisture, and thermal cycling — no internal arcing or shorts over time
  • Direct Fitment: Exact drop-in replacement for OEM 129700-4400, 129700-4420, 33410-24F10, F6T549, and F6T547 — no wiring modifications required
  • High-Output Secondary: 9825 kV minimum cranking output ensures reliable ignition even with marginal battery voltage or carbon-fouled spark plugs
  • Extended Service Life: Reinforced housing and strain-relieved connectors resist cracking from engine heat cycles — tested to >50,000 miles of street use

Technical Specifications

  • Primary Resistance: 1.8-2.2 ohms
  • Secondary Resistance: 7.5-10.5 kohms
  • Output: 9825 kV minimum @ cranking
  • Construction: Copper windings, epoxy resin potting
  • OEM Reference: 129700-4400, 129700-4420, 33410-24F10, F6T549, F6T547, 33410-35F10
  • Vehicle Fitment: Suzuki GSX1300R Hayabusa, GSXR1000 (99-19), GSX650F, Bandit 650/1250, GSXR750 (96-99)
  • Quantity: 4 coils per set
  • Connector: Factory-style push-on with locking tab

Application Scenarios

The Fire Pulse ignition coil set is the go-to replacement for Suzuki sportbike owners experiencing hard starting, rough idle, misfire codes, or a noticeable loss of high-RPM power. It applies equally to track-day GSX-R builds that see sustained high RPM, to Gen 1 and Gen 2 Hayabusa owners looking for a reliable replacement before a long tour, and to Bandit 1250 commuters where a misfiring cylinder kills fuel economy. The epoxy potting makes these coils significantly more resistant to vibration-induced failure than the original open-frame designs — a common failure point on high-mileage Suzuki engines. For shops performing multi-bike services, stocking one SKU that covers the Suzuki sportbike platform (GSX-R, GSX, Bandit, GSF) simplifies inventory.

Frequently Asked Questions

Q: Will these fit a 2008 Suzuki GSXR600?

A: Yes. The 129700-4400 platform is shared across GSXR600, GSXR750, and GSXR1000 models from 1999-2019. These coils will drop in without modification.

Q: What is the difference between these and the OEM Suzuki coils?

A: The electrical specifications are identical to OEM. The key difference is the epoxy-resin encapsulation, which provides better vibration damping and longer service life than the factory's open-frame construction.

Q: Do I need to replace spark plugs at the same time?

A: It is strongly recommended. Worn spark plugs increase the voltage demand on the ignition coil and can cause premature failure. If your existing plugs have more than 10,000 miles, replace them with the set.

Q: What is the torque spec for the coil mounting bolts?

A: The Suzuki service manual specifies 10 Nm (7.4 ft-lbs) for the mounting bolts. Over-tightening can crack the coil housing or strip the threads in the cylinder head cover.

Q: How do I diagnose which cylinder has a bad coil?

A: Use a multimeter to check primary resistance (1.8-2.2 ohms) between the two terminals on each coil. An open circuit or short circuit indicates a failed coil. You can also swap coils between cylinders; if the misfire code follows the swapped coil, the coil is the culprit.

Q: What tools do I need to replace the ignition coils on my GSX-R?

A: Basic hand tools only: a 10mm socket for the coil mounting bolts, dielectric grease for the spark plug boots, and a torque wrench set to 10 Nm. The coils sit on top of the spark plugs under the fuel tank. On most GSX-R models, you will need to lift or remove the fuel tank (supported by a prop rod) and disconnect the electrical connectors by pressing the locking tab and pulling straight up. Total job time: 20-30 minutes for a first-timer, under 927 minutes for someone who has done it before.

Q: These coils have different OEM numbers listed. How do I know which one matches my bike?

A: The OEM numbers (129700-4400, 129700-4420, 33410-24F10, F6T549, F6T547) are supersession and cross-reference numbers for the same coil platform used across Suzuki's GSX-R, GSX, and Bandit families. Any of these numbers indicates the same physical coil. The primary difference is the connector orientation (straight vs. angled on some early models). Our coils use the standard straight connector that fits all GSX-R models from 1999-2019. If you have an early model (pre-2001) with angled connectors, the straight connector will still fit but the wire routing may be slightly different.

Q: Can I replace just one coil instead of the full set of four?

A: While it is technically possible to replace a single failed coil, we strongly recommend replacing all four as a set. The remaining three coils have experienced the same number of heat cycles, vibration exposure, and electrical stress as the failed one. Replacing only the failed coil typically results in another coil failure within 6-12 months, requiring a repeat of the labor-intensive fuel-tank lift procedure. Replacing all four at once adds approximately $80 to the parts cost but eliminates the labor cost of a second replacement.

Customer Reviews

Payment and Security

PayPal

お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません

発送予定

You may also like

Recently Seen