{"product_id":"the-three-kilo-anycubic-pla-plus-filament","title":"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool","description":"\u003cdiv class=\"product-narrative\"\u003e\n\u003cp\u003eFilament is the one consumable where the cheap roll and the good roll look identical on the spool and behave nothing alike on the machine. The Three Kilo is ANYCUBIC PLA+ in a three kilogram spool, which is the size that matters for anyone printing more than one project a month: fewer changes, fewer partial spools in the cupboard, and one continuous batch of colour that will not shift shade halfway through a large print.\u003c\/p\u003e\n\u003cp\u003eThe specification that decides whether a roll prints reliably is diameter tolerance, and this one is controlled to plus or minus 0.02 millimetres. At 1.75 millimetres nominal, that tolerance is what keeps extrusion volume consistent from the first metre to the last, because a filament that wanders by 0.1 millimetre changes the flow rate enough to show as banding on a vertical wall. The winding is deliberately tidy and cross-laid rather than loosely spooled, which is what stops the tangle that ruins a fourteen hour print at hour twelve.\u003c\/p\u003e\n\u003cp\u003ePLA+ is not PLA with a marketing suffix. The modified formulation raises toughness and impact resistance, so parts survive being dropped and clips survive being flexed, while keeping the printing behaviour people like about PLA: no enclosure, no heated chamber, low warp, and a finish that takes paint and glue cleanly. It holds dimensional stability well enough that large flat parts stay flat, and the layer adhesion is consistent rather than the brittle snap that standard PLA shows on thin walls.\u003c\/p\u003e\n\u003cp\u003eThe material is imported, non-toxic and vacuum sealed with desiccant, which matters more at three kilograms than at one: a spool that absorbs moisture over months prints with popping and stringing, and a spool this size takes long enough to use that packaging is part of the specification. Compatibility is broad enough to be uninteresting, which is the point, and shelf life is stated at two years sealed.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eBuy filament by the batch, not by the panic.\u003c\/em\u003e\u003c\/p\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-features\"\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul style=\"list-style:none;padding:0;\"\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eThree kilogram spool\u003c\/strong\u003e Roughly three times the print time of a one kilo roll, so one batch carries a whole project in a single consistent colour.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003ePlus or minus 0.02mm tolerance\u003c\/strong\u003e Controlled diameter keeps extrusion volume stable, which is what prevents banding on tall vertical walls.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eTidy cross-wound spool\u003c\/strong\u003e Wound to resist tangling, so a long print does not fail at hour twelve on a crossed strand.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003ePLA+ toughness\u003c\/strong\u003e Higher impact resistance than standard PLA, so clips flex and dropped parts survive.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eLow warp, no enclosure\u003c\/strong\u003e Prints on an open machine, which keeps the barrier to entry where it should be.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eVacuum sealed with desiccant\u003c\/strong\u003e Moisture protection matters at this spool size, because the roll is open for months.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eConsistent colour batch\u003c\/strong\u003e One spool, one dye lot, so a multi-part assembly does not shift shade between parts.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eWide printer compatibility\u003c\/strong\u003e Works on the large majority of FDM printers and 3D printing pens at standard PLA temperatures.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-specs\"\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cul style=\"list-style:none;padding:0;\"\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e PLA+ modified polylactic acid\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eDiameter:\u003c\/strong\u003e 1.75mm, tolerance plus or minus 0.02mm\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eSpool weight:\u003c\/strong\u003e 3kg net\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eColours:\u003c\/strong\u003e White, Grey, Black\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003ePrint temperature:\u003c\/strong\u003e Standard PLA+ range, typically 200 to 220 degrees Celsius\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eBed adhesion:\u003c\/strong\u003e Heated bed recommended, 50 to 60 degrees Celsius\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eTensile behaviour:\u003c\/strong\u003e High toughness with impact resistance, reduced brittleness versus standard PLA\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eWarping:\u003c\/strong\u003e Low, prints without an enclosure\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e Vacuum sealed with desiccant\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eShelf life:\u003c\/strong\u003e 2 years sealed\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eCompatibility:\u003c\/strong\u003e Most FDM printers and 3D printing pens\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eShips from:\u003c\/strong\u003e United States or Germany warehouse, depending on variant\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-applications\"\u003e\n\u003ch3\u003eWhere It Belongs\u003c\/h3\u003e\n\u003cp\u003eIt suits the workshop that prints brackets, jigs, enclosures and replacement knobs, where a failed print costs an afternoon rather than a photo opportunity. It suits the hobbyist who has graduated from one kilo rolls and is tired of running out mid-assembly, and it suits anyone producing the same part repeatedly who wants one dye lot across the batch. The three colours are the practical ones: white for painting and for light diffusion, grey for showing surface detail, black for functional parts that should not look like prototypes.\u003c\/p\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-faq\"\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cdiv style=\"margin-bottom:15px;\"\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Does a 3kg spool fit a standard printer?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA: Not all of them. A three kilogram spool is physically larger than a one kilo roll, so check the spool holder diameter and clearance on your machine. Many printers need an external side-mounted holder or a bearing spool holder for this size.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:15px;\"\u003e\n\u003cp\u003e\u003cstrong\u003eQ: What temperatures should I print at?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA: Start at 205 degrees Celsius nozzle and 60 degrees bed, then adjust in five degree steps. PLA+ typically wants slightly more heat than standard PLA for the best layer adhesion.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:15px;\"\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Will it string?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA: Less than wet filament, and more than dry filament. If you see fine hair between travel moves, dry the spool at 45 degrees for four hours before blaming the settings, since moisture is the usual cause.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:15px;\"\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Is PLA+ food safe?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA: No 3D printed part is food safe in a practical sense, because layer lines harbour bacteria and brass nozzles contain lead. Use it for models, jigs and functional parts, not for cups or cutlery.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:15px;\"\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Can I paint it?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA: Yes. Grey and white take primer and acrylic well. Sanding with 400 then 800 grit before priming gives a finish close to injection moulded, and PLA+ sands without the fuzz that standard PLA shows.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:15px;\"\u003e\n\u003cp\u003e\u003cstrong\u003eQ: What is the shelf life actually?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA: Two years sealed. Once opened, moisture absorption is the limiting factor, so store it in a sealed bag with desiccant, or in a dry box if the room is humid.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:15px;\"\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Does the ±0.02mm tolerance apply across the whole spool?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eA: It is a controlled specification across the production run rather than a spot check at the start of the spool. That is what matters for flow consistency, since a diameter that drifts mid-print changes extrusion volume.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-promise\"\u003e\n\u003ch3\u003eThe EastSupplier Promise\u003c\/h3\u003e\n\u003cp\u003eEvery unit ships from inspected stock held by our own team, not from a blind dropship queue. Orders placed before 3pm warehouse time leave the same working day, and each parcel carries a tracking number you can follow from dispatch to doorstep. If a unit arrives damaged or does not match this listing, we replace or refund it inside 30 days.\u003c\/p\u003e\n\u003cul style=\"list-style:none;padding:0;\"\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eStock checked daily:\u003c\/strong\u003e the inventory figure on this page is live, not a placeholder.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eTechnical answers in English:\u003c\/strong\u003e a human replies to product questions within one business day.\u003c\/li\u003e\n\u003cli style=\"padding:8px 0;border-bottom:1px solid #f0f0f0;\"\u003e\n\u003cstrong\u003eNo surprise fees:\u003c\/strong\u003e the price you see is the price at checkout.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-gallery\" style=\"margin-top:30px;text-align:center;\"\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S7dc6c2ec87754f12adc30510dd057c7d4.webp?v=1754607646\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Sbab731c6602d40bfb1d395835fc974c0j.webp?v=1754607646\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S933057900b574a24ab086e358abe2e56R.webp?v=1754607646\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S784d800d27314481a36043cfe1165380n.webp?v=1754607646\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S0390db6f6626461f8287293ca45eead12.webp?v=1754607647\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S8fe6e79f71c842389b61b6c9c64cf11bt.webp?v=1754607646\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S55ae537146114e65b8c415d6ef3f5195f.webp?v=1754607647\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S819d4cbbcd064e77a5684e5268036713h.webp?v=1754607647\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Se31174b06c224b5396d6749d576d9213p.webp?v=1754607646\" alt=\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\" style=\"max-width:100%;height:auto;margin:4px 0;\" loading=\"lazy\"\u003e\n\u003c\/div\u003e\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\/\",\"@type\":\"Product\",\"name\":\"The Three Kilo | ANYCUBIC PLA+ Filament 1.75mm, 3kg Spool\",\"brand\":{\"@type\":\"Brand\",\"name\":\"EastSupplier\"},\"url\":\"https:\/\/eastsupplier.com\/products\/the-three-kilo-anycubic-pla-plus-filament\",\"offers\":{\"@type\":\"Offer\",\"price\":\"106.01\",\"priceCurrency\":\"USD\",\"availability\":\"https:\/\/schema.org\/InStock\",\"url\":\"https:\/\/eastsupplier.com\/products\/the-three-kilo-anycubic-pla-plus-filament\"},\"aggregateRating\":{\"@type\":\"AggregateRating\",\"ratingValue\":\"4.8\",\"reviewCount\":\"3\"}}\u003c\/script\u003e","brand":"East Supplier Platform","offers":[{"title":"White 3kg \/ United States","offer_id":47204994023647,"sku":"1005007937503272-White 3kg-United States","price":106.01,"currency_code":"USD","in_stock":true},{"title":"White 3kg \/ GERMANY","offer_id":47204994089183,"sku":"1005007937503272-White 3kg-GERMANY","price":87.18,"currency_code":"USD","in_stock":true},{"title":"Grey 3kg \/ GERMANY","offer_id":47204994384095,"sku":"1005007937503272-Grey 3kg-GERMANY","price":98.78,"currency_code":"USD","in_stock":true},{"title":"Grey 3kg \/ United States","offer_id":47204994580703,"sku":"1005007937503272-Grey 3kg-United States","price":104.53,"currency_code":"USD","in_stock":true},{"title":"Black 3kg \/ United States","offer_id":47204994777311,"sku":"1005007937503272-Black 3kg-United States","price":106.01,"currency_code":"USD","in_stock":true},{"title":"Black 3kg \/ GERMANY","offer_id":47204994842847,"sku":"1005007937503272-Black 3kg-GERMANY","price":87.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S7dc6c2ec87754f12adc30510dd057c7d4.webp?v=1754607646","url":"https:\/\/eastsupplier.com\/ja-es\/products\/the-three-kilo-anycubic-pla-plus-filament","provider":"EastSupplier Platform","version":"1.0","type":"link"}