説明
Heat is the quiet reason car mounts fail. A phone clamped to a vent in July runs navigation, screen at full brightness, wireless coil pushing current, and the whole assembly sits in a pocket of air that the dashboard has been heating all afternoon. The Cool Dock attacks that specific problem: a Qi2 magnetic charger with a semiconductor cooling plate and an internal fan, mounted on a 360 degree ball joint that grips the vent blade instead of the windshield.
The cooling stack is the engineering worth paying for. A semiconductor chip draws heat out of the mirrored contact surface that meets the back of the phone, and a small fan moves it away behind the housing. Charging efficiency is rated at 85 percent, which is high for a wireless car setup, and the reason the phone does not throttle mid-route. Power delivery is 15W, 10W, 7.5W and 5W depending on the handset, over a Type-C input, and it expects an 18W QC 3.0 car adapter as its source. Qi2 certification from the Wireless Power Consortium is the other half of the story: alignment is magnetic and repeatable, so the coil lines up on the first placement rather than the third.
Mounting is deliberately mechanical. The ball joint rotates through a full circle and holds angle under load, so the phone can sit portrait for maps or landscape for a dash camera without the arm creeping down over a speed bump. The vent clip is the telescoping type that reaches past the slats, which is what stops the common failure of cheap holders popping off when a passenger knocks the console. The mirrored contact face is not cosmetic either; a smooth surface is far less likely to grind grit into the phone back than a soft rubber pad.
A phone that stays cool on a long drive is not a luxury. It is the difference between arriving with a route and arriving with a dead handset.
What the Cooling Stack Changes
- ✦ Semiconductor cooling chip pulls heat off the contact plate while the coil is charging.
- ✦ Internal fan exhausts that heat behind the housing instead of into the phone.
- ✦ Qi2 certified alignment from the Wireless Power Consortium for repeatable coil placement.
- ✦ 15W, 10W, 7.5W and 5W output tiers negotiated by the handset, 85 percent efficiency.
- ✦ Mirrored contact surface protects the phone back from scuffing and grit.
- ✦ 360 degree ball joint with a telescoping vent clamp that holds angle under load.
- ✦ Type-C input with a Type-C cable in the box, no proprietary connector to lose.
Technical Specifications
- Charging Standard Qi2, certified by the Wireless Power Consortium
- Output 15W / 10W / 7.5W / 5W, negotiated by handset
- Input Type-C, DC 12V 1.75A, 9V 1.67A, 5V 2A
- Power Source 18W QC 3.0 car adapter required, not included
- Efficiency 85 percent
- Cooling Semiconductor cooling chip plus internal fan
- Contact Surface Mirrored plate, scratch resistant
- Mount Vent clip, telescoping, 360 degree ball joint
- Compliance CE, RoHS
- In The Box Charger, vent holder, Type-C to Type-C cable
Fitted Where the Dashboard Actually Gets Hot
Rideshare and delivery drivers are the obvious case, because a phone on charge and on screen for six hours is a phone that will otherwise throttle in the sun. Long-distance drivers get the second benefit, which is that magnetic alignment lets the handset come off with one hand at a fuel stop instead of a two-handed unclip. Owners of newer iPhones with the magnetic ring built in get the full 15W tier; Android handsets work with a magnetic ring on the case or a magnet-safe case, and the dock will still charge at the negotiated rate. Anyone who has watched a vent mount sag under a heavy phone will notice the telescoping clamp first, because that is the part that fails on cheap designs.
Before You Order
Q. Do I need a special charger in the car socket?
Yes, and it is the most common reason a wireless car charger underperforms. The dock needs an 18W QC 3.0 adapter as its supply. A standard 5V USB port will charge slowly or not at all.
Q. Will it charge an Android phone?
Charging works with any Qi-compatible handset. The magnetic hold is a separate question and depends on the phone having a magnet array or a magnet-safe case, which is why the listing mentions a magnetic ring for non-Apple devices.
Q. Does the fan make noise?
There is a small fan inside and it is audible in a quiet cabin at close range. In normal driving with the engine and ventilation running it disappears into the background, which is the trade for keeping the coil from cooking the battery.
Q. Will the vent clip fit vertical or horizontal blades?
The clamp is the telescoping jaw type that reaches past the slat, so either orientation works as long as the blade has a reasonable depth. Very thin decorative slats are the one case to check before ordering.
Q. Can I use a thick case?
Qi2 alignment tolerates a normal case, but very thick or metal-backed cases reduce both hold strength and charging rate. A magnetic ring case is the safest combination.
Q. Does the dock block the vent in winter?
It sits in front of the blade rather than filling the opening, so airflow continues around the housing. Position it in the center of a blade rather than across two, which keeps the vent usable.
Customer Reviews
Payment and Security
お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません
