The Bench Frame | ECU BDM Frame with Adapters, Probes and LED Bar

East Supplier PlatformSKU: 1005007218906098-BDM Frame-france

Color: BDM Frame
価格:
$82.58

税込み 送料計算済み チェックアウト時

在庫:
残り9個

説明

The hardest part of reading an ECU is not the software. It is holding four probes on four pads the width of a hair while the board stays absolutely still. Anyone who has done a MED17 bench read with a hand-held probe knows the failure mode: the tenth of a second when the pin slips, the checksum that fails, the flash that has to be recovered before the customer comes back for the car. The BDM frame exists to remove the hand from the equation. It is a bracket that turns a delicate manual contact into a mechanical one.

The frame is cut from plexiglass, which is the right material for the job: rigid enough to hold probe geometry across a session, electrically inert, and transparent so the operator can see the pads they are landing on. Four probe pens with spring-loaded, scalable tips seat onto the BOOT and CNF1 pads and stay there. The jumper block on the acrylic board replaces the usual business of soldering a lead to a pad and hoping the joint survives removal. Because the geometry is fixed, a second read on the same board type takes seconds instead of minutes.

Two versions are stocked. The LED version adds a light bar across the frame, powered from the 12 V supply of the ECU rig itself, which is what makes late-night bench work on a dark green PCB practical rather than guesswork. Both versions accept the standard tuning ecosystem: original FGTECH, BDM100, CMD, KESS, KTAG and KTM100 tools, and the adapter set covers both genuine and non-genuine FGTECH housings. This is a bench accessory, not a magic box. It does not read anything by itself, and it will not make a clone tool behave like an original, but it will stop the probe from moving, which is where most failed reads actually begin.

Precision is not a technique. It is a fixture that holds the technique still.

Key Features

  • ✦ Mechanical probe holding: four spring-loaded pens stay seated on BOOT and CNF1 pads through a full read.
  • ✦ Transparent plexiglass frame keeps the pads visible while the geometry stays locked.
  • ✦ Optional LED light bar, powered from the 12 V ECU supply, for dark boards in poor workshop light.
  • ✦ Jumper block replaces soldered leads, so a board can be connected and released without leaving solder on a pad.
  • ✦ Adapter set covers original FGTECH as well as the common non-original housing dimensions.
  • ✦ Works with BDM100, CMD, KESS, KTAG, KTM100 and FGTECH bench tools already in the shop.
  • ✦ Repeatable geometry: the second read on a known board type takes seconds, not minutes.

Technical Specifications

  • Type: BDM probe frame for ECU bench work
  • Frame material: plexiglass (acrylic)
  • Versions: standard frame, or frame with LED light bar
  • Probes: 4 spring-loaded probe pens with scalable tips
  • Adapters: 4-piece adapter set for FGTECH BDM100 housing variants
  • LED power: 12 V from the ECU programming device supply
  • Compatibility: BDM100, FGTECH, CMD, KESS, KTAG, KTM100 and similar bench tools
  • Connection: plug-in jumpers, no permanent soldering required
  • Package, LED version: 1 frame, 4 probe pens, 4 adapters, 4 connect cables
  • Package, standard version: 1 frame, 4 adapters, pin set

Where It Belongs

This belongs on the bench of anyone who reads and writes ECU flash memory for a living: a tuning workshop doing stage work on VAG, BMW and Mercedes petrol engines, a mobile diagnostics technician who needs a repeatable setup that packs into a case, an immobiliser and mileage specialist working on MED17 and similar boards, or a serious enthusiast who has already bought the software and discovered that the physical contact is the part nobody warns them about. It is also the accessory a trainer hands to a new technician, because a frame that holds the probes turns an error-prone manual skill into a procedure that can be taught.

Questions Buyers Ask

Q: Does the frame read the ECU on its own?

A: No. It is a physical holder for the probes. You still need a BDM programmer and its software, such as BDM100, FGTECH, KESS, KTAG or CMD. The frame only makes the connection stable and repeatable.

Q: Which version should I order, standard or LED?

A: The LED version if you work in a normal workshop where the board is often in shadow or the bench light is behind you. The standard version is fine for a bright dedicated bench. The LED bar runs from the 12 V supply you already use for the programming device.

Q: Will it fit a non-original FGTECH unit?

A: Yes. The adapter set is dimensioned to fit both original FGTECH and the common non-original housings. If your unit has a non-standard housing, check the adapter spacing before ordering.

Q: Do I still have to solder anything?

A: Normally no. The jumper block and connect cables replace the soldered lead. Some boards still need a direct connection to a specific pad, and in that case the frame holds position while you make it, which is exactly when you want both hands free.

Q: Can it be used on the car or only on a bench?

A: It is designed for bench work on a removed ECU. Working in the engine bay with the board in place is possible on some vehicles but awkward, and the frame is not sealed against moisture or dirt.

Q: How do I know the probes are contacting properly?

A: Read the chip ID first. A correct ID confirms all four contacts before you attempt a read or a write, and it is the cheapest possible test in terms of time lost if a probe is off the pad.

Customer Reviews

Customer Reviews

Based on 3 reviews
67%
(2)
33%
(1)
0%
(0)
0%
(0)
0%
(0)
H
Henrietta L.
Adapters fit my non-original FGTECH housing

I was worried the adapter set would only line up with a genuine FGTECH unit. It fitted my clone housing without any filing. Read a VAG board twice in a row as a repeatability test and the geometry was identical both times, which is exactly what I bought it for.

G
Georgiana Z.
LED bar earns its place, frame is bulkier than expected

The LED light bar is genuinely useful on dark green boards and running it off the 12V supply from the programming device is neat. The frame itself is thicker than the photos suggest, so on a tight bench it takes up more room than I planned. Probes are solid and the tips grip well.

C
Cassius M.
Held the probes through a full MED17 read

First bench read with this frame and the difference is obvious. The four probe pens stayed exactly where I seated them for the entire read, which never happened with a hand-held probe. Checksum passed first time. The jumper block also saved me from soldering a lead to the BOOT pad, which is the part I always dread.

Payment and Security

PayPal

お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません

発送予定

You may also like

Recently Seen