Descrizione
The rear of a sedan is where design either resolves or trails off. A trunk lid that ends in a flat horizontal plane leaves the eye nowhere to go, and the fix is not a wing bolted on in a parking lot. It is a lip that continues the roofline arc and closes the profile.
This trunk spoiler is molded in ABS and finished in a carbon-fiber look that matches the weave direction of factory interior trim closely enough that the two read as one design decision. It sits flush on the trailing edge of the boot lid, raises the visual shoulder of the car by a few centimeters, and adds a genuine aerodynamic lip at speed rather than a decorative shelf.
Fitment is the whole story with body parts, so it is stated plainly: Audi A3, S3 and RS3 sedan, model years 2014 through 2020. It does not fit the Sportback, the wagon or the convertible, whose boot lids are shaped differently. Installation is a double-sided tape job on a clean, degreased surface, with no drilling and nothing to reverse if the car is later sold.
A spoiler should look like it was drawn with the car, not added after delivery.
What Makes It Different
- RT style lip profile — a low, wide extension that follows the trunk crown instead of rising above it, so the silhouette stays clean from three quarters.
- ABS construction — resilient to stone chips and UV, and light enough that tape alone holds it at highway speed.
- Carbon-fiber look finish — a directional weave that reads correctly next to OEM carbon trim and interior inlays.
- Sedan-specific fitment — molded for the 2014 to 2020 A3, S3 and RS3 boot lid, not a universal trim cut to fit.
- No-drill installation — pre-applied double-sided tape plus a supplied tape strip; nothing irreversible happens to the car.
- Reversible modification — remove it with heat and adhesive remover and the panel underneath is unchanged.
Technical Specifications
- Fitment: Audi A3 / S3 / RS3 sedan, 2014 to 2020
- Not Compatible: Sportback, wagon (Avant) and convertible body styles
- Material: ABS plastic
- Finish: Carbon fiber look, UV-stable
- Type: Rear boot trunk spoiler lip
- Placement: Rear, trailing edge of the boot lid
- Installation: Double-sided automotive tape, no drilling
- Included: 1 x rear trunk spoiler, 1 x double-sided tape
- Certification: CCC
- Note: Fitting instructions not included; professional installation recommended
Where It Belongs
The car this belongs on is a daily driven A3 sedan, an S3 that sees weekend canyon roads, or an RS3 whose owner wants the rear end to look as deliberate as the front. It suits a car being brought back to factory-plus condition after a parking lot scuff, and it suits a lease vehicle where every change has to be reversible at hand-back. Detailers fit it before a ceramic coating so the tape edge is sealed in the same pass. On a black or gray car the carbon look disappears into the paint and reads simply as a better resolved profile; on white or red it becomes a clear design line.
Questions Buyers Ask
Q: Will this fit my 2018 Audi A3 Sportback?
A: No. This spoiler is molded for the sedan boot lid only. The Sportback, the Avant wagon and the cabriolet use a different rear profile and this part will not sit flush.
Q: Does it need drilling?
A: No drilling is required. The spoiler attaches with automotive double-sided tape. Clean the panel with isopropyl alcohol, warm the tape and the panel slightly, and hold pressure for a minute per section.
Q: How long does the tape hold?
A: With correct surface preparation the tape holds indefinitely at highway speed. Avoid applying it in cold weather below about 15 degrees Celsius, and do not wash the car for 48 hours afterward.
Q: Is the carbon fiber real?
A: The finish is a carbon-fiber look over ABS plastic, not a carbon weave laminate. That is what keeps the part affordable and impact resistant, and the visual match to OEM carbon trim is close.
Q: Can it be removed later?
A: Yes. Warm the tape with a heat gun on low setting, work a plastic trim tool underneath, and clean the residue with adhesive remover. The paint underneath is unaffected.
Q: Does it improve downforce?
A: It adds a functional lip at the trailing edge and stabilizes airflow off the boot lid, but this is a street part. Expect a visual and high-speed stability improvement rather than measurable track downforce.






Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.
