Descrizione
Copper Does Not Negotiate. It Only Transmits. Every serious electrical build has exactly one point of failure that nobody photographs: the wire. Amplifiers starve for current through undersized cable. Inverters overheat because a PVC jacket turns brittle in an engine bay. Battery relocations lose voltage across a run that was never rated for the load. The Conduit Line was selected to remove that variable. This is a super-soft silicone power cable built around a stranded pure-copper conductor, sized from 14 AWG down to 26 AWG, and cut in continuous lengths from five metres to fifty. It is the unglamorous component that decides whether the glamorous components actually work.
Silicone is the reason this cable survives where ordinary wire fails. The jacket remains flexible from minus sixty degrees Celsius to plus two hundred degrees Celsius, which means it does not crack in a winter engine bay and does not soften against a hot manifold. The conductor is stranded, not solid, with individual strands of roughly 0.08 millimetres, giving the cable the fatigue resistance that vibration environments demand while still carrying a DC rating of up to 3000 volts. It is certified to CE and FCC, supplied in matched red and black pairs for polarity-clear runs, and it is available across eight distinct gauges so that a single order can service an entire project rather than one circuit of it.
Choose the gauge by current, not by habit. Fourteen and sixteen AWG carry the heavy loads: battery relocation, inverter feeds, winch and starter circuits, high-output LED bars. Eighteen through twenty-two AWG handle sensor runs, relay triggers, indicator lighting and small solar interconnects. The fine gauges are for signal work where flexibility inside a tight enclosure matters more than current capacity. Because the insulation is silicone rather than PVC, the wire stays supple even when routed through grommets, around corners and inside loom that has to bend rather than kink.
A cable is not a commodity. It is the part of the build that decides whether the rest of it holds up.
Key Features
- ✦ Super-soft silicone jacket, flexible from -60 °C to +200 °C
- ✦ Stranded pure copper conductor with approximately 0.08 mm individual strands
- ✦ Eight gauge options from 12 AWG to 26 AWG for load and signal work alike
- ✦ DC 3000V dielectric rating for high-voltage and inverter applications
- ✦ Heat resistant and flame retardant silicone insulation that will not go brittle
- ✦ Matched red and black polarity pairs supplied together
- ✦ Continuous cut lengths of 5 m, 10 m, 20 m and 50 m
- ✦ CE and FCC certified for professional and OEM installation
Technical Specifications
- Insulation: Super-soft silicone rubber
- Conductor: Stranded pure copper, approx. 0.08 mm strands
- Gauge range: 12, 14, 16, 18, 20, 22, 24, 26 AWG
- Available lengths: 5 m / 10 m / 20 m / 50 m
- Voltage rating: DC 3000V
- Working temperature: -60 °C to +200 °C
- Colours: Red and black
- Certification: CE, FCC
- Application: Car battery, inverters, LED lighting, RC and solar
- Conductor type: Stranded, high-flex
Application Scenarios
The Conduit Line is aimed at anyone who has ever traced a fault back to the wire. Car audio installers use the heavy gauges to feed amplifiers and subwoofer banks without voltage sag, and use the fine gauges for remote turn-on and signal runs. Van, camper and overland builders route it between lithium banks, DC-DC chargers, solar controllers and interior lighting because the silicone jacket shrugs off heat cycles that destroy PVC. RC and drone builders value the 20 to 26 AWG range for its flexibility at the joint. Workshop and industrial users buy the fifty-metre cuts to keep a spool on the bench rather than ordering wire metre by metre. In every case the reasoning is identical: the run is permanent, and redoing it is expensive.
Frequently Asked Questions
Q: Can this cable be used to relocate a car battery to the boot?
A: Yes. For a typical relocation, 14 or 16 AWG is appropriate for the main positive feed over the lengths offered here, with a matching ground return. If your starter draw is high, size up and keep the run as short as the layout allows.
Q: Is the conductor genuinely copper, or copper-coated aluminium?
A: It is stranded pure copper with individual strands of approximately 0.08 mm. Copper-clad aluminium is lighter and cheaper, but it carries less current for the same gauge and work-hardens at the joint. This is the real material.
Q: Which gauge should I choose for a 12 volt LED lighting circuit?
A: For interior and accent lighting, 18 to 22 AWG is normally sufficient. If you are driving a high-power light bar drawing more than ten amps, step up to 14 or 16 AWG to keep voltage drop negligible.
Q: How hot can this wire get before the insulation is affected?
A: The silicone jacket is rated for continuous operation up to 200 degrees Celsius and remains flexible down to minus 60 degrees Celsius, so it tolerates engine bay heat and winter cold without cracking or embrittling.
Q: Can I solder and crimp this wire easily?
A: Yes. Because the strands are fine and the jacket is soft, the cable strips cleanly, crimps well into standard terminals and accepts solder without wicking heat far up the conductor.
Q: Why silicone instead of the usual PVC insulation?
A: Silicone stays flexible across a far wider temperature range and does not harden or crack with age. In vibration-heavy or heat-cycled installations, that difference is the whole service life of the harness.
Q: Do lengths come as a pair of red and black, or as single runs?
A: Both colours are offered across the gauge and length range, so you can order matched polarity pairs for a single circuit or a single colour for a specific run.
Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.