Descrizione
An engine control unit is a closed book by design. The manufacturer writes the calibration, seals the case, and assumes the owner will never need the first page. The KESS and KTAG suite is built for the people who do, the tuners, the diagnosticians and the workshops who need to read and rewrite that calibration without cutting a single wire they cannot restore.
The kit pairs two of the most established platforms in the trade. The KESS V5.017 handles engine and gearbox programming over the vehicle port, so a standard road car can be read and flashed through its own diagnostic connector. The KTAG V7.020 covers the cases where the port is locked or the module sits on the bench, using boot and bench modes to reach the processor directly with the correct protocol for the device in front of you. Together they cover the vast majority of European, Asian and American vehicles that arrive at a tuning bay. Correct protocol selection is handled by the software, so an operator selects the vehicle and the platform negotiates the handshake.
Four status LEDs keep the operator informed through every phase of a write, which matters because a programming session is the one task where patience and certainty are everything. The hardware is driver-supported on standard Windows systems, updates are supplied online, and the tooling has earned a following among professionals precisely because it does the single most important thing a programming interface can do, which is finish cleanly.
This is not a cable and a licence. It is the key to the part of the car the factory never meant you to open.
Key Features
- ✦ Two established platforms in one kit: KESS V5.017 for vehicle-port programming and KTAG V7.020 for bench and boot work
- ✦ Reads and writes engine and gearbox control units across European, Asian and American vehicles
- ✦ Boot, bench and OBD modes for modules that are locked at the diagnostic connector
- ✦ Four LED status indicators reporting progress through every phase of a write session
- ✦ Correct protocol negotiated automatically from the selected vehicle profile
- ✦ Standard Windows driver support with no proprietary dongle dependency
- ✦ Online software updates that keep the vehicle list current
Technical Specifications
- Brand: EKETOOL
- Hardware versions: KESS V5.017 and KTAG V7.020
- Communication interface: OBD-II and USB
- Operating modes: OBD, bench and boot read-write
- Coverage: European, Asian and American vehicles
- Indicators: Four LED status lights for write phases
- Host software: Windows platform with signed drivers
- Updates: Online delivery to keep vehicle profiles current
- Certification: CE
- Use case: ECU tuning, cloning, repair and calibration work
Application Scenarios
A tuning workshop keeps this kit beside the dyno because a customer who arrives for a stage-one map expects the file to be read, edited and written in a single visit. A diagnostic specialist reaches for it when a replacement control unit must be cloned to VIN-match a repaired vehicle, and a specialist facing a sealed or port-locked module switches to boot mode rather than turning the job away. Fleet maintenance teams use it to restore original calibrations before resale, and enthusiasts restoring an older car depend on it when the dealer tooling no longer covers the platform. In each case the requirement is identical: an interface that speaks the right protocol and returns the module intact.
Frequently Asked Questions
Q: Do I need both units or can I use one?
A: The two platforms cover different work. KESS programs through the vehicle connector for most road cars, while KTAG reaches modules on the bench or in boot mode that the port cannot access. Keeping both means a locked module is never a dead end.
Q: Which vehicles are supported?
A: Coverage spans a wide range of European, Asian and American makes. The software selects the protocol from the vehicle profile, and the online update keeps the list aligned with newer platforms.
Q: Will programming damage the control unit?
A: No, provided the correct protocol and a stable supply are used. The four LED indicators confirm each phase of the write so an interruption is visible rather than silent. A stabilised power source during a write is always recommended.
Q: What computer does it run on?
A: A standard Windows laptop is sufficient. The hardware is driver-supported and does not depend on a proprietary dongle to operate.
Q: Is it suitable for a repair shop rather than only a tuning specialist?
A: Yes. Cloning a replacement module, restoring a factory calibration and recovering a bricked unit are routine repair tasks that the same kit handles.
Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.
