Descrizione
The Garage Floor Is Where Good Work Goes to Die. Not because the work is bad, but because the body gives out first. A brake job is forty minutes of kneeling on concrete, and by the second caliper your knees have made a decision your hands have to live with. The roller seat exists to delete that variable. You sit, you roll, you stay at the height of the work instead of dropping to the floor and climbing back up every time a socket rolls out of reach.
Under the cushion is a steel frame rated to 300 lbs (136 kg), which is well beyond what a seated technician will ever load it with, and the whole unit weighs 12.3 lbs (5.6 kg), light enough to lift over a sill with one hand. The cushion is 17.7 by 9.8 inches, wide enough that you are sitting rather than balancing, and it sits 15.4 inches off the ground so you can reach a wheel arch without folding your spine. Four 4-inch (101.6 mm) casters move in any direction on a smooth slab, and three 10.2 by 9.8 by 2 inch trays carry the sockets, bolts and clips that would otherwise end up under the car.
The behaviour change is unglamorous and total. You stop standing up to think. The tray holds the fasteners in the order you removed them, so reassembly stops being an exercise in memory. Detailing the lower half of a door, a rocker panel, a wheel face - all of it becomes a seated task instead of a series of squats. Overall footprint is 25.2 by 13.2 by 15.4 inches, so it lives against a wall when the job is finished and does not become furniture in a single-car garage.
You do not get closer to the machine by kneeling. You get closer by staying.
Key Features
- ✦ 300 lb (136 kg) rated steel frame built for seated work
- ✦ Four 4-inch casters that move in any direction on a smooth slab
- ✦ 17.7 by 9.8 inch padded cushion, 15.4 inches off the floor
- ✦ Three 10.2 by 9.8 by 2 inch trays, sized for sockets and removed fasteners
- ✦ 12.3 lb total weight - light enough to lift and hang on a wall
- ✦ Compact 25.2 by 13.2 by 15.4 inch footprint for single-bay garages
- ✦ Model BLC9010, shipped flat with hardware and assembly instructions
Technical Specifications
- Model BLC9010
- Load capacity 300 lbs / 136 kg
- Cushion size 17.7 x 9.8 in / 450 x 250 mm
- Caster diameter 4 in / 101.6 mm
- Tool trays 3 trays, 10.2 x 9.8 x 2 in each
- Overall dimensions 25.2 x 13.2 x 15.4 in
- Net weight 12.3 lbs / 5.6 kg
- Frame Powder-coated steel
- Assembly Flat-pack, tools included
- Use Garage, workshop, detailing bay, home DIY
Where It Belongs
A roller seat earns its place in any garage where the work happens below waist height: brake and suspension jobs, oil changes on a car you cannot raise very far, wheel arch and rocker panel detailing, under-dash electrical work, and the long afternoon of cleaning alloy wheels one spoke at a time. It is equally at home in a detailing bay, where technicians spend entire days at the level of a door handle, and in a home garage where the floor is the only flat surface available. If you work on motorcycles, it doubles as a low stool for chain and brake work.
Questions, Answered
Q: Will it fit under a car that is not lifted?
A: The seat sits 15.4 inches high overall, so clearance depends on your car. Most sedans and SUVs on jack stands will clear it; a car sitting on its tyres will not. Measure the gap between the slab and the lowest point of the sill before you buy.
Q: Do the casters work on a rough floor?
A: They roll cleanly on a smooth concrete slab or epoxy floor. On cracked, gravel or heavily pitted surfaces you will feel every edge, and small debris can stall a caster. Sweep the bay first; that is true of every roller seat.
Q: How long does assembly take?
A: Roughly fifteen to twenty minutes with the included hardware. The casters bolt to the frame base and the trays mount to the seat frame. No special tools are required.
Q: Can the trays hold bolts and tools at the same time?
A: Each tray is 10.2 by 9.8 by 2 inches with a raised lip. It is sized for sockets, wrenches and the fasteners from one corner of the job rather than an entire toolbox.
Q: Is 300 lbs a real rating?
A: It is the rated static load of the steel frame and the cushion platform. In practice a seated technician plus tools is far below it, which is the point: the frame is not working near its limit.
Q: How do I clean it?
A: Wipe the cushion with a damp cloth and mild detergent, and brush debris out of the casters after a dirty job. Do not pressure-wash the casters; the bearings are not sealed against a jet.
Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.