The Cell Keeper | 5A Active Battery Balancer for LiFePO4, LiPo and LTO

East Supplier PlatformSKU:1005007181232095-3-4S 5A-United States

Color: 3-4S 5A
Prezzo:
$35.05

Tasse incluse spese di spedizione calcolata al pagamento

Disponibilità:
Disponibile

Descrizione

Battery packs rarely die of old age. They die of disagreement. One cell drifts a few millivolts high, the BMS sees that cell reach full first and ends the charge for the entire pack, and the remaining capacity is never delivered. Another drifts low and trips the discharge cutoff while every other cell still has energy to give. On paper the pack is healthy, and in use it delivers a fraction of what its cells can still hold.

The Cell Keeper is a capacitor-based active balancer. Where a resistor board burns the excess off as heat, this board moves charge from the higher cells into the lower ones, which is the difference between discarding energy and redistributing it. Balance current runs from 0 to 5.5 A and tapers as the cells converge, voltage accuracy sits within 5 mV, and the working range of 1.8 to 4.5 V per cell covers ternary lithium, LiFePO4 and LTO chemistries across 3S to 24S.

Under the lid sits an ultra-low internal-resistance MOS array on a 2 oz copper board, a manual sleep switch, a quiescent draw of about 12 mA, and under-voltage sleep that cuts the board below 3.0 V so a stored pack is not flattened by its own equalizer. Recommended pack capacity is 60 to 300 Ah. Four variants cover the voltage families: 3-4S, 12-16S, 17-21S, and a smart board for 10-24S.

Chemistry decides how much energy a pack can hold. Balance decides how long it keeps holding it.


Why Capacitors, Not Resistors

  • Capacitive energy transfer instead of resistive burn-off, so almost nothing is lost as heat
  • Balance current from 0 to 5.5 A, tapering automatically as the cells converge
  • Voltage accuracy within 5 mV, which is the resolution that actually matters at cell level
  • Works across ternary lithium, LiFePO4 and LTO chemistries from 3S to 24S
  • Under-voltage sleep below 3.0 V and a standby draw under 0.1 mA
  • 2 oz copper PCB with low internal-resistance MOS devices
  • Manual sleep switch for storage and transport

Board Specifications

  • Balance methodCapacitive active charge transfer
  • Balance current0 to 5.5 A
  • Voltage accuracyWithin 5 mV
  • Working voltage1.8 V to 4.5 V per cell
  • String range3S to 24S across four variants
  • ChemistriesTernary lithium, LiFePO4, LTO
  • Recommended pack size60 to 300 Ah
  • Quiescent currentAbout 12 mA
  • Standby currentUnder 0.1 mA with under-voltage sleep
  • Board2 oz copper with low-Rds(on) MOS array

Packs This Belongs In

This belongs in any pack that is built from many cells in series and expected to last. A camper van bank balancing 4S 280 Ah LiFePO4 cells, a 16S solar storage pack where one cell always lags, a 20S scooter or e-bike battery that loses range long before its cycle count suggests it should, and a 24S LTO pack used for high-current bursts all suffer the same barrel effect: the weakest cell sets the ceiling for the whole. Wiring the balancer in parallel with the cells and leaving it connected lets the pack equalise while it rests, which is where the capacity that was silently lost comes back.

Pack Builder Questions

Q: Is this a BMS, or does it replace one?

It is a balancer, not a protector. The BMS still handles over-charge, over-discharge, over-current and short protection; this board's job is keeping the cells at the same voltage so the BMS is not tripped early by one outlier.

Q: Which variant do I need?

Match the variant to your string count: 3-4S for small packs, 12-16S for most 48 V lithium builds, 17-21S for higher-voltage packs, and the smart 10-24S board where the pack covers a wide range.

Q: What pack capacity is it designed for?

The manufacturer recommends packs from 60 to 300 Ah. Below 60 Ah the 5 A current is more than the pack needs; far above 300 Ah a single board works harder than intended.

Q: Does it get hot?

It should not. Capacitive transfer moves charge between cells rather than dissipating it, so heat is minimal compared with a resistor balancer working at the same current.

Q: Will it drain my pack while the vehicle sits?

Quiescent draw is around 12 mA, and below 3.0 V per cell the board enters under-voltage sleep at under 0.1 mA. That is why the sleep behaviour matters for a pack stored through winter.

Q: Does it work with lead-acid batteries?

No. The working range of 1.8 to 4.5 V per cell and the chemistry list are specific to lithium cells. Lead-acid has a different voltage curve and needs a different device.

Q: Do I need to configure anything?

No configuration is required. Connect the balance leads to the cells, and the board begins equalising as soon as it sees voltage. A manual sleep switch is provided for storage.

Q: Why does the current drop as the pack balances?

Because the voltage difference driving the transfer shrinks as the cells converge. The taper is the sign the board is working, not a fault.

Q: Can I run two boards on one large bank?

You can, provided each board covers its own group of cells and the groups are wired consistently. For packs above 300 Ah, split the bank rather than overloading one board.

Q: Are batteries or a charger included?

No. This is the equaliser board only. Cells, charger and BMS are separate, which is why the board is sold by string count rather than as a complete pack.

Customer Reviews

Customer Reviews

Based on 3 reviews
67%
(2)
33%
(1)
0%
(0)
0%
(0)
0%
(0)
O
Orla L.
Sleep mode means the pack is not dead in spring

Left a 20S scooter pack parked from November to March with the board connected, and the cells were still within tolerance when I came back. The under-3 V sleep is the reason I picked this one over a resistor balancer.

N
Niall T.
It balances, it does not protect

Works exactly as described, but read the listing properly: this is an equaliser, and your BMS still has to do over-voltage and over-current. Two weeks in a 16S pack with no drama. Wires are not supplied, so order the balance leads at the same time.

M
Maren R.
4S 280Ah bank finally charges to full

One cell used to hit 3.65 V first and the BMS cut the charge while the others sat at 3.38 V. A week with this connected and the spread is down to a few millivolts, and the pack takes noticeably more charge before the cutoff. Silent in operation, no heat that I can feel.

Payment and Security

PayPal

Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.

Previsione di spedizione

You may also like

Recently Seen