Description
A torn refrigerator gasket is one of the most expensive cheap problems in a kitchen. The door still closes, the light still goes off, and nobody notices that the compressor is now running overtime to hold a temperature it used to keep for free. It shows up later, as frost in the freezer, a fridge that never quite gets cold, and an electricity bill that climbed without a new appliance arriving.
The Cold Seal is supplied as 7 m of elastic plastic gasket material that is cut to your measurements rather than to a model number. You send the height and width of the door opening, along with a photo of how the existing gasket folds over the door edge, and the profile is matched to your unit before it ships. That is what makes one product fit chest freezers, top freezer refrigerators and the older cabinets that no parts catalogue still lists.
Fitting is a patient job rather than a technical one. Unfold the gasket, lay it flat for 24 hours so the kinks from packaging relax, warm it gently to soften the profile, then work it into the door channel a section at a time. A gasket that sits flat seals flat, and the compressor gets its rest back.
The cheapest repair in the kitchen is the one that stops the leak.
Key Features
- ✦ Seven metres of elastic plastic gasket material, cut to the sizes you measure
- ✦ Custom profile match based on photos of your existing door gasket
- ✦ Fits chest freezers, top freezer refrigerators and older cabinets without a parts listing
- ✦ Restores the door seal that keeps the compressor from running overtime
- ✦ Cuts frost build-up in the freezer and helps airflow between compartments
- ✦ Simple hand fitting, no special tools, with a clear reshape and heat method
- ✦ Supplied as continuous material so long door edges are covered without joins
Technical Specifications
- Material: Elastic plastic gasket, refrigerator grade
- Length: 7 m per order, cut to your measurements
- Type: Refrigerator and chest freezer door seal, universal fit with custom sizing
- Fit method: Matched from photos of the original gasket profile
- How to order: Send gasket photos plus height and width in centimetres, then we confirm the size and quantity
- Install time: About 30 to 60 minutes for a single door
- Prep step: Lay the gasket flat for 24 hours to remove packaging kinks
- Sealing check: Paper test, a sheet should resist being pulled out with the door shut
- Care: Wipe with warm soapy water, avoid solvents
- Colour: Supplied in the profile colour available at dispatch
Where It Fits
This is a repair part for the awkward cases. A chest freezer in a garage, a beer fridge in a bar, a rental kitchen with an appliance from a brand that no longer stocks spares. If the door your gasket sits on has a straight edge and a channel for the profile to fold into, the Cold Seal can be cut to it. Landlords, property managers and appliance repair techs order it as stock because one roll covers several doors when the sizes are planned together.
Frequently Asked Questions
Q: How do I measure for a custom gasket?
Measure the height and width of the door opening in centimetres and photograph the corner where the gasket folds over the door. Send both before paying so the profile can be matched to your unit.
Q: What happens if I do not send measurements?
The order ships with the standard uncut size, and it may not fit your door. Custom cutting depends on the measurements you provide, so always send them first.
Q: Does it come in a specific colour?
The colour depends on what is in stock at dispatch. Colour does not affect sealing performance, only appearance.
Q: Can I cut the gasket myself?
Yes. Many customers trim the final length with sharp scissors once the profile is seated, which is normal practice for universal gasket material.
Q: How do I know if my old gasket is failing?
Run the paper test. Close the door on a strip of paper and pull. If it slides out easily at any point, the seal is leaking there. Frost in the freezer and a warm fridge are the other common signs.
Q: Will one roll cover my whole fridge?
One roll is 7 m, which generally covers a single door. Freezer and fridge doors usually need separate quantities, so measure both before ordering.
Q: How do I measure for a custom gasket?
Measure the height and the width of the door opening in centimeters and send both numbers with your order. Converting feet and inches before you send them avoids the most common fitting error.
Q: Does the gasket include a magnetic strip?
This is a fitted seal that presses against the door frame and does not include a magnetic insert. If your door closes with a magnetic strip today, that strip stays on the cabinet and the new gasket seats against it.
Q: Can I cut it to length myself?
Yes. The material cuts with household scissors, and a square cut at both ends seals much better than a torn edge.
Q: What should I do if it arrives folded?
Unfold it and let it rest at room temperature for a day before fitting. Warm water or a hair dryer on low heat also removes the creases left by shipping.
Q: How long should a replacement gasket last?
Two to five years is typical for a well fitted gasket. Wiping the seal twice a year and keeping food debris out of the groove usually decides which end of that range you get.
The EastSupplier Promise
Every order ships from a warehouse we control, inspected against the specification sheet above before it leaves the dock. If a unit arrives outside that specification, we replace it or refund it.
- Verified stock — listed inventory is real, not backorder padding.
- Tracked dispatch — a working tracking number within 3 business days.
- Direct support — one team answers sourcing, spec and after-sales questions.
- Wholesale ready — tiered pricing on request for resellers and project buyers.
Customer Reviews
Payment and Security
Vos informations de paiement sont gérées de manière sécurisée. Nous ne stockons ni ne pouvons récupérer votre numéro de carte bancaire.