Description
The Fastener Decides the Tool. Every stripped head in a workshop traces back to the same moment, which is when the wrong bit was fitted to a fastener that was never going to forgive it. A hex bit in a Torx head rounds the star into a circle. A worn spline bit chews a Ribe bolt into scrap. Forty pieces in one tray is not an indulgence, it is the shortest route to never having that moment again, because the correct profile is always within reach of the ratchet.
Two drive sizes in one footprint. The set runs both 3/8 and 1/2 inch drive, so the same tray serves the small work under a dashboard and the larger work on a suspension arm without a second case on the bench. Bits are machined from hardened steel and finished to a tolerance that seats fully into the fastener rather than riding on the tips, which is the difference between transferring torque and destroying the head.
Organised so the right bit takes one second to find. The tray labels each position by profile, so the socket is chosen by looking rather than by trying three of them against the fastener. Extensions and adaptors sit in the same case, which means the whole assembly goes to the job as a unit. Closed, it is a flat case that lives in a drawer or a bag rather than a pile of loose sockets at the bottom of a toolbox.
It is not a collection of bits. It is the end of a class of mistake.
What the Tray Covers
- ✦ Forty pieces in a single labelled tray
- ✦ Both 3/8 and 1/2 inch drive in the same case
- ✦ Allen key, Torx, hex, star and spline profiles
- ✦ Hardened steel bits machined to a seating tolerance
- ✦ Profile-labelled positions for one-second selection
- ✦ Extensions and adaptors carried in the same case
- ✦ Suits hand ratchets as well as power drivers
- ✦ Flat closed case stores in a drawer or a bag
Tool Record
- Set contents: 40 pieces, bits plus extensions and adaptors
- Drive sizes: 3/8 inch and 1/2 inch
- Profiles: Allen key, Torx, hex, star, spline
- Material: Hardened steel, machined finish
- Finish: Corrosion-resistant plating
- Fit: Tolerance-cut to seat fully in the fastener
- Compatibility: Hand ratchets, breaker bars and power drivers
- Storage: Profile-labelled tray inside a flat case
- Use: Automotive, appliance, machinery and furniture work
- Origin: Mainland China
Where the Forty Pieces Work
An automotive bay uses the full range on a single vehicle, because a modern car mixes Torx on interior trim, hex on engine covers and spline on driveline fasteners within a couple of metres of each other. An appliance or white-goods technician works at the small end, where the 3/8 drive and the finer profiles reach fixings that a 1/2 inch ratchet cannot physically address. A machinery maintenance fitter wants both drives in one case because the walk back to the toolbox is the cost that a complete tray removes. A furniture or flat-pack assembler uses the hex and Allen profiles almost exclusively, but benefits from the same labelled tray when a supplier sends a bolt in a metric size the supplied key does not match. A home workshop buys it once and stops buying single sockets at retail prices, which is usually the day the set pays for itself.
Bit Set Questions
Q: Which drive sizes does the set cover?
A: Both 3/8 inch and 1/2 inch drive are included in the same case, so the small work and the heavier work are covered without a second tray on the bench. Adapters in the set let you move between the two where a specific ratchet is the only one to hand.
Q: What fastener profiles are included?
A: Allen key, Torx, hex, star and spline across the forty positions. That spread is chosen to cover the profiles a modern vehicle and a modern appliance actually use, rather than repeating one profile in a dozen near-identical sizes.
Q: Will the bits break under a breaker bar?
A: They are machined from hardened steel and cut to a seating tolerance, so they are built for hand tools rather than for impact drivers. Use an impact-rated set with a power impact gun, and keep this tray for ratchets, breaker bars and hand drivers.
Q: Do the bits strip the fastener heads?
A: The opposite, provided the correct profile is used. The failure mode that rounds a head is a bit that does not seat fully, which is why the tray is labelled by profile and why the bits are cut to tolerance. Choosing the profile that actually matches the bolt is what protects the fastener.
Q: Does it come with extensions?
A: Extensions and adaptors travel in the same case as the bits, so the whole assembly goes to the job together. That is what makes the tray practical on a vehicle rather than a bench-only set.
Q: How is the case organised?
A: Each position is labelled by profile, so a bit is chosen by looking at the tray rather than by testing several against the fastener. Closed, the case is flat enough to live in a drawer or a tool bag.
Customer Reviews
Payment and Security
Vos informations de paiement sont gérées de manière sécurisée. Nous ne stockons ni ne pouvons récupérer votre numéro de carte bancaire.