Description
PLA is the easy answer and ABS is the capable one. PETG is the spool that stays on the machine.
Glycol-modified PET is what you get when a manufacturer takes the strength of ABS and removes most of the reasons people hate printing it. It lays down with noticeably better layer adhesion than PLA, survives a knock without shattering, and shrugs off moisture and ultraviolet light that would leave a PLA part brittle within a season. It also does not need a heated chamber to behave: a nozzle held between 230 and 250 degrees with a bed between 60 and 80 degrees is enough, and an enclosed or semi-enclosed printer simply removes the draughts that cause lifting on larger footprints. The material is translucent with a high-gloss surface, so printed light shades, vases and layered signage read as finished objects rather than as texture.
Each spool carries 1.1 kg of filament at a nominal 1.75 mm diameter, which works out to roughly 320 metres of usable material and makes the arithmetic of a project straightforward before you start it. Extrusion is consistent, the strand is solid rather than foamed, and the finish is free of the bubbles that show up in cheaper stock and translate into rough walls and inconsistent flow. Shelf life is stated at one year, and the four stocked colourways cover the practical range: white for light diffusion, black for brackets and hardware, clear for anything that has to pass light, and LY for parts that should look deliberate.
Buy it for the parts you intend to keep, not for the test prints.
Why PETG Over PLA
- Layer bonding — layers weld rather than sit on each other, so parts survive impact instead of delaminating
- Moisture and UV tolerance — outdoor brackets, garden fittings and car interior parts hold up where PLA goes brittle
- Slight flex — thin clips and snap-fit geometries bend rather than crack
- Translucent, high-gloss finish — light shades, vases and layered panels read as finished surfaces
- Bubble-free strand — consistent diameter means consistent flow and cleaner walls
- 1.1 kg / 320 m per spool — enough material to plan a project rather than a test
Technical Specifications
- Material — PETG (glycol-modified polyethylene terephthalate)
- Brand — JAYO
- Diameter — 1.75 mm
- Net weight — 1.1 kg per spool
- Filament length — Approximately 320 metres
- Print temperature — 230-250 degrees C
- Bed temperature — 60-80 degrees C, set to the surface in use
- Printing environment — Enclosed or semi-enclosed space recommended for large parts
- Surface finish — Translucent, high transparency, good gloss
- Form — Solid strand, 100 percent bubble-free
- Shelf life — 1 year in sealed, dry storage
- Colourways — White, Black, Clear (CR), LY
- Compatibility — FDM 3D printers and 3D pens accepting 1.75 mm filament
- Origin — Mainland China
What It Gets Used For
This is the spool for functional printing. Brackets and adapters that will be loaded, enclosures that will be handled, hooks and clips that need to flex without cracking, jigs and shop fixtures that live in a garage where the temperature moves. It is also the sensible choice for anything decorative that will be seen in daylight or near a window, because the gloss and the translucency hold up and the colour does not chalk the way unstabilised PLA does. People printing for robotics, RC vehicles, cosplay armour and home repair use PETG precisely because a failed part at that point costs a print job rather than a shelf ornament, and the 320 metres on the spool is enough to make mistakes without ordering again.
Printer Questions
Q: Do I need an enclosure?
A: Not for small parts. Larger, flatter geometries warp when air moves across them, so an enclosed or semi-enclosed printer is the safer setup. A cardboard shield around the frame achieves the same thing.
Q: Why is PETG stringing on my machine?
A: Wet filament and hot nozzles both cause it. Dry the spool, drop the nozzle to the low end of the 230-250 range, and raise retraction slightly. PETG is more prone to fine hairs than PLA at the same settings.
Q: How should I store it between projects?
A: Sealed with desiccant, out of sunlight, and that applies to every spool on the shelf. Stated shelf life is one year, but a spool left open in a humid room will print badly long before that.
Q: Does it stick to the bed too well?
A: It grips harder than PLA, which is an advantage until you try to remove a large thin part. Let the bed cool, and use a release agent or a textured surface on very flat geometries.
Q: Can I print it on a stock hotend?
A: Yes. At 230-250 degrees it sits inside the range of standard all-metal and PTFE-lined hotends rated for the temperature. Bowden and direct drive both work; PETG is not an abrasive material.
Q: Which colour should I start with?
A: Black for brackets and hardware, white if you are printing light diffusers or want a neutral base, clear for anything that needs to pass light, LY if the part will be visible.
Customer Reviews
Payment and Security
Vos informations de paiement sont gérées de manière sécurisée. Nous ne stockons ni ne pouvons récupérer votre numéro de carte bancaire.