Description
The last metre of a bathroom is where most of its maintenance budget goes. Bottles standing on a ledge collect water rings, tip over, and leave a ring of dried soap that takes a scraper to remove. A wall-mounted dispenser removes the bottle from the equation: one fixed point, one pump, one drip line that lands in the basin instead of on the tile.
The Press & Pour holds 600 millilitres in a moulded ABS body measuring roughly 8 by 6.5 by 23.5 centimetres. ABS is the right plastic for the job because it tolerates the alcohols and surfactants in hand soap, shampoo and body wash without crazing, and it survives the accidental elbow that a glass or ceramic reservoir would not. A clear window runs down the front so the level is visible from standing height, which ends the guessing game that leads to a pump full of air in the middle of a shower.
Mounting takes one drill point and two screws, or an adhesive plate on tile where drilling is not an option. The pump head is a simple piston rather than a spring-loaded commercial valve, which means it delivers a consistent dose without needing priming after a refill and without the seal failure that turns a cheap dispenser into a leak. Capacity is the quiet advantage: 600ml is roughly three standard retail bottles, so refills happen monthly rather than weekly, and the container itself is the packaging.
Fill it, hang it, and the ledge stays clear. That is the entire specification, and it is the reason the product exists.
Installation height decides whether a dispenser feels considered or improvised. Set the pump head roughly twenty to thirty centimetres above the basin rim so a hand arrives under it naturally and the drip lands inside the bowl rather than behind it. In a shower, mount it at chest height beside the mixer, out of the direct spray, where the reservoir stays cool and the soap does not separate. Leave enough clearance under the pump for a full press, including the knuckle. Two screws into a stud or a wall plug is the durable answer, and adhesive is the reversible one for rental kitchens.
Key Features
- ✦ 600ml reservoir equivalent to roughly three retail soap bottles
- ✦ ABS body resistant to alcohols and surfactants in soap and shampoo
- ✦ Clear front window for checking the level without opening the unit
- ✦ Wall mounted to keep the basin ledge clear and dry
- ✦ Single-piston pump that doses consistently with no priming after refill
- ✦ Suitable for hand soap, shampoo, body wash, lotion and sanitiser
- ✦ Screw or adhesive mounting for tile, plaster and laminate surfaces
Technical Specifications
- Capacity: 600ml
- Material: ABS plastic
- Dimensions: approx. 8 x 6.5 x 23.5cm
- Mounting: wall mounted, screw or adhesive
- Pump type: manual piston, press action
- Level indicator: front viewing window
- Compatible liquids: hand soap, shampoo, body wash, lotion, gel sanitiser
- Fill method: top lid, removable for refilling and rinsing
- Recommended use: bathroom, kitchen, toilet, shower, utility room
- Package contents: one dispenser with mounting fixings
Application Scenarios
Households mount one beside the kitchen sink for washing-up liquid and a second in the shower for shampoo, which removes two bottles from the wet shelf. Small offices and clinics fit them in shared washrooms where loose bottles disappear and leak. Cafes and restaurants use them behind the counter because a wall unit cannot be knocked over during service, and the refill interval is predictable enough to schedule. Landlords and holiday-let operators fit them between guests, since a 600ml reservoir plus a visible level means a cleaner can check and refill in seconds.
Frequently Asked Questions
Q: Will thick liquids like body wash pump properly?
A: Yes, up to the point where the liquid will not flow on its own. Very thick creams should be thinned slightly or used in a wide-neck pump, since a narrow piston struggles against high viscosity.
Q: Can it be mounted on tile without drilling?
A: Yes. Clean the tile, dry it fully, and use the adhesive plate on a flat area. Avoid grout lines, since adhesive bonded to grout rather than tile holds far less weight when the reservoir is full.
Q: Does the pump need priming after a refill?
A: Two or three presses. Refill before the reservoir empties completely and it primes almost immediately, because the tube never draws air into the piston chamber.
Q: How do I clean the inside?
A: Remove the lid, fill with warm water and a little white vinegar, pump through until clear, then rinse. Do this between different liquids so the new product does not inherit the old scent.
Q: Is it suitable for alcohol-based sanitiser?
A: Gel sanitiser works well. High-percentage liquid alcohol evaporates faster and can dry the piston seal over months, so the gel form is the safer choice for a long-term installation.
Q: What is the maximum load on adhesive mounting?
A: A full 600ml reservoir weighs well under a kilogram, which most quality adhesive plates hold comfortably on smooth tile or glass. Rough or dusty surfaces need the screw fixings instead.
Q: Can I use it for dish soap in a commercial kitchen?
A: Yes, provided the soap is not a heavy degreaser gel designed for industrial dilution. Standard washing-up liquid pumps cleanly and the ABS body tolerates it indefinitely.
Q: Does the reservoir come off for cleaning?
A: The top lid lifts and the body stays on the wall. Fill, pump through warm water, and rinse in place, which avoids having to remove the fixings every time the liquid is changed.
Q: What happens if the pump clogs?
A: Usually a thickened residue at the nozzle. Draw warm water through the pump, then clear the outlet with a pin. Do not push a wire down the tube, since the piston seal sits just behind it.
The EastSupplier Promise
- ✦ Every unit inspected before dispatch, with the specifications listed on this page checked against the shipped item.
- ✦ Tracked international shipping with a dispatch window confirmed at checkout.
- ✦ Direct replacement for units that arrive damaged or fail within the warranty period, handled by message rather than by form.
- ✦ Sourcing support for bulk and repeat orders, including consolidated shipping and custom quantity pricing.
Product Gallery
Customer Reviews
Payment and Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.